AIR CONDITIONING UNIT (for TMMK Made) REASSEMBLY


  1. INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY


    1. B000NDD

      Check that the slots, links and gears of the No. 1 air conditioning radiator damper servo sub-assembly are positioned in the correct orientation as shown in the illustration.

    2. Face the contact surfaces of the No. 1 air conditioning radiator damper servo sub-assembly and air conditioning radiator assembly for the No. 1 air conditioning radiator damper servo sub-assembly upward.

    3. Rotate the link of the air conditioning radiator assembly all the way to the left as shown in the illustration.

      B000HHA

    4. Rotate the link of the air conditioning radiator assembly to the bottom as shown in the illustration and confirm that the mode switching duct hole is fully closed.

      B000JCRE02
      Text in Illustration
      *a Mode Switching Duct Hole - -

    5. Rotate the lever of the air conditioning radiator assembly to the top as shown in the illustration.

      B000HV6

    6. Rotate the link of the air conditioning radiator assembly to the in-line position as shown in the illustration.

      B000LTUE02
      Text in Illustration
      *a In-line Position - -
    7. B000N5OE05
      Text in Illustration
      *a Vinyl Tape

      Wrap the upper and lower links with vinyl tape to hold them in the in-line position.

    8. Install the link of the No. 1 air conditioning radiator damper servo sub-assembly to the link guide pin (A) of the air conditioning radiator assembly as shown in the illustration.

      B000HSWE08
      Text in Illustration
      *1 No. 1 Air Conditioning Radiator Damper Servo Sub-assembly - -
      *a Guide *b No. 1 Air Conditioning Radiator Damper Servo Sub-assembly Slot
      *c Link Guide Pin (A) *d Link Guide Pin (B)

    9. Install the guide hole of the No. 1 air conditioning radiator damper servo sub-assembly to the guide pin of the air conditioning radiator assembly as shown in the illustration.

    10. Temporarily install the screw (up to 4 or 5 threads).

      Note


      • Make sure that the link guide pin (B) is inserted in the No. 1 air conditioning radiator damper servo sub-assembly slot.

      • Avoid tilting the air conditioning radiator assembly during installation. This helps to prevent the link guide pins from coming out of position.

    11. B000LOB

      Lift the No. 1 air conditioning radiator damper servo sub-assembly slightly to create clearance.

    12. Move the air conditioning radiator assembly gear so that the alignment holes of the No. 1 air conditioning radiator damper servo sub-assembly and air conditioning radiator assembly are aligned.

      B000KY1E02
      Text in Illustration
      *a No. 1 Air Conditioning Radiator Damper Servo Sub-assembly Alignment Hole *b Air Conditioning Radiator Assembly Alignment Hole
      *c Air Conditioning Radiator Assembly Alignment Gear Alignment Hole - -
    13. B000NNO

      Insert a screwdriver into the alignment holes as shown in the illustration.

    14. Make sure that all the links and gears are in the positions shown in the illustration.

      B000NB3E02
      Text in Illustration
      *a Screwdriver is inserted into alignment holes. *b Link guide pin is inserted.
      *c Link is positioned to left side. *d Link is positioned at bottom.
      *e Each link guide pin is inserted in its air outlet control servo motor slot. *f Lever is positioned at top.
      *g Links are in-line. - -
    15. B000INU

      Push the loose fitting No. 1 air conditioning radiator damper servo sub-assembly into position.

      Note


      • Make sure that the No. 1 air conditioning radiator damper servo sub-assembly are fully pushed into position.

      • After pushing the servos into position, keep them in place by holding them until the screws are installed.

      Tech Tips

      Push the No. 1 air conditioning radiator damper servo sub-assembly until a click sound is heard.

    16. Remove the screwdriver.

    17. B000JK7

      Fully install the top screw, and then install the No. 1 air conditioning radiator damper servo sub-assembly with the 2 screws.

    18. Remove the vinyl tape.

  2. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY


    1. B000J01

      Install the heater radiator unit sub-assembly to the air conditioning radiator assembly as shown in the illustration.

    2. B000KY2

      Install the clamp with the screw.

    3. B000MCV

      Engage the 3 claws to install the heater clamp.

  3. INSTALL NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY


    1. B000IDHE02
      Text in Illustration
      *a Reference Point

      Using the reference point, install the No. 2 air conditioning radiator damper servo sub-assembly with the 2 screws.

  4. INSTALL NO. 1 COOLER THERMISTOR


    1. B000JG6E05
      Text in Illustration
      *a Fixed Part
      *b Sensor Part

      Install the No. 1 cooler thermistor as shown in the illustration.

      Part Length
      A 34.3 mm 1.35 in.
      B 20.9 mm 0.823 in.
      C 50 mm 1.97 in.

      Note


      • Be sure to insert the No. 1 cooler thermistor only once because reinserting it into the same position will not allow it to be firmly secured.

      • When reusing the No. 1 cooler evaporator sub-assembly, insert the No. 1 cooler thermistor one row next to the one that has been used previously (X in the illustration).

      • After inserting the No. 1 cooler thermistor, do not apply excessive force to the wire.

      • Directly insert the No. 1 cooler thermistor until the edge of the plastic case "a" comes into contact with the No. 1 cooler evaporator sub-assembly "b".

    2. Engage the 2 clamps.

  5. INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY


    1. B000I5K

      Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces. Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.

      Compressor Oil
      ND-OIL 8 or equivalent
    2. B000M91

      Install the No. 1 cooler evaporator sub-assembly to the blower assembly as shown in the illustration.

  6. INSTALL BLOWER ASSEMBLY WITH COOLER EVAPORATOR SUB-ASSEMBLY


    1. Engage the 4 claws.

    2. Install the blower assembly with cooler evaporator sub-assembly with the 6 screws.

  7. INSTALL COOLER EXPANSION VALVE


    1. B000NQ4

      Using a 4 mm hexagon socket wrench, install the cooler expansion valve with the 2 hexagon bolts.

      Torque:
      3.5 N*m  { 36 kgf*cm, 31 in.*lbf }

  8. INSTALL AIR CONDITIONING HARNESS ASSEMBLY


    1. B000J55

      Engage the 5 clamps to install the air conditioning harness assembly.

    2. Connect the 5 connectors.

    3. B000HPR

      Install the heater packing as shown in the illustration.

  9. INSTALL ASPIRATOR


    1. B000JTP

      Engage the 2 claws to install the aspirator.

  10. INSTALL COOLER THERMISTOR HOSE


    1. B000LTC

      Engage the clamp to install the cooler thermistor hose.

  11. INSTALL NO. 6 HEATER TO REGISTER DUCT ASSEMBLY


    1. B000J5W

      Engage the 2 claws and 2 guides to install the No. 6 heater to register duct assembly as shown in the illustration.

  12. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY


    1. B000IW7

      Engage the guide and 2 claws to install the No. 1 air duct sub-assembly as shown in the illustration.