SEAT BELT WARNING SYSTEM (w/ Occupant Classification System) TERMINALS OF ECU


  1. CHECK COMBINATION METER ASSEMBLY


    1. Disconnect the I18 combination meter assembly connector.

      B000KMHE06

    2. Measure the resistance according to the value(s) in the table below.

      Tech Tips

      Measure the values on the wire harness side with the connector disconnected.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I18-20 (ES) - Body ground BR - Body ground Ground Always Below 1 Ω

      If the result is not as specified, there may be a malfunction in the wire harness.

    3. Reconnect the I18 combination meter assembly connector.

    4. Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I18-1 (B) - Body ground W - Body ground Battery power supply Always 11 to 14 V
      I18-13 (IG+) - Body ground L - Body ground

      Ignition power supply

      (IG signal)

      		 Ignition switch off Below 1 V
      I18-13 (IG+) - Body ground L - Body ground

      Ignition power supply

      (IG signal)

      		 Ignition switch ON 11 to 14 V

      If the result is not as specified, the combination meter assembly may have a malfunction.

  2. CHECK AIRBAG SENSOR ASSEMBLY

    B000IDKE49
    Terminal No. Terminal Symbol Destination
    N5-10 LBE+ Front seat inner belt assembly LH
    N5-18 LBE- Front seat inner belt assembly LH
    O7-16 FSR+ Occupant detection ECU
    O7-24 FSR- Occupant detection ECU

  3. CHECK OCCUPANT DETECTION ECU


    1. Measure the voltage according to the value(s) in the table below.

      B000JCEE20
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specification
      d11-1 (+B) - d11-3 (GND) W - W-B Battery Always 11 to 14 V
      d11-2 (DIA) - d11-3 (GND) GR - W-B Diagnosis (DLC3) Ignition switch ON, GTS not connected to DLC3 Below 1 V
      d11-3 (GND) - Body ground W-B - Body ground Ground Always Below 1 V
      d11-4 (FSR-) - d11-3 (GND) Y - W-B Airbag sensor assembly communication line Always Below 1 V
      d11-5 (BGND) - d11-3 (GND) P - W-B Front passenger buckle switch ground line Always Below 1 V
      d11-6 (IG2) - d11-3 (GND) B - W-B Power source Ignition switch ON 11 to 14 V
      d11-7 (FSR+) - d11-4 (FSR-) L - Y Airbag sensor assembly communication line Ignition switch ON Pulse generation
      d11-8 (BSW) - d11-5 (BGND) G - P Front passenger buckle switch line Always Pulse generation
      d8-1 (SVC1) - d8-5 (SGD1) R - G Front occupant classification sensor power supply line Ignition switch ON 4.9 to 5.1 V
      d8-2 (SVC3) - d8-6 (SGD3) GR - W Rear occupant classification sensor power supply line Ignition switch ON 4.9 to 5.1 V
      d8-3 (SIG1) - d8-5 (SGD1) P - G Front occupant classification sensor signal line Ignition switch ON Pulse generation
      d8-4 (SIG3) - d8-6 (SGD3) Y - W Rear occupant classification sensor signal line Ignition switch ON Pulse generation

      If the result is not as specified, the occupant detection ECU may have a malfunction.