REAR SEAT RECLINING CONTROL CABLE (for TMC, TMMR Made) REMOVAL


  1. REMOVE REAR SEAT HEADREST ASSEMBLY

  2. REMOVE REAR SEATBACK ASSEMBLY LH


    1. Disconnect the rear seat outer belt assembly from the rear seat center shoulder belt guide.

    2. Fold down the rear seatback assembly LH.

    3. B000ML8E01
      Text in Illustration
      *1 Fastener

      Disengage the fastener as shown in the illustration.

    4. w/o Seat Heater System:


      1. B000LMV

        Remove the 2 bolts and rear seatback assembly LH.

        Note

        Be careful not to damage the vehicle body.

    5. w/ Seat Heater System:


      1. B000LMV

        Remove the 2 bolts and disconnect the rear seatback assembly LH.

      2. B000I3I

        Disconnect the connector.

      3. Disengage the clamp and remove the rear seatback assembly LH.

        Note

        Be careful not to damage the vehicle body.

  3. REMOVE REAR SEATBACK ASSEMBLY RH


    1. Fold down the rear seatback assembly RH.

    2. B000N8GE01
      Text in Illustration
      *1 Fastener

      Disengage the fastener as shown in the illustration.

    3. w/o Seat Heater System:


      1. B000J3W

        Remove the 2 bolts and rear seatback assembly RH.

        Note

        Be careful not to damage the vehicle body.

    4. w/ Seat Heater System:


      1. B000J3W

        Remove the 2 bolts and disconnect the rear seatback assembly RH.

      2. B000H9I

        Disconnect the connector.

      3. Disengage the clamp and remove the rear seatback assembly RH.

        Note

        Be careful not to damage the vehicle body.

  4. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. B000IRWE01

      Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.

      Standard Measurement
      a 100 mm (3.94 in.) or less

      Note

      Be sure to hold the part of the rear seat cushion assembly directly next to the rear seat cushion lock hooks when lifting it up. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.

    2. w/ Seat Heater System:


      1. Disconnect the connector.

      2. B000KQW

        Disengage the 2 clamps.

    3. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.

      Note

      Be careful not to damage the vehicle body.

  5. REMOVE REAR SEAT CUSHION LOCK HOOK


    1. B000LZB

      Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  6. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide LH.

    2. B000HI6

      Remove the bolt.

    3. Disengage the hook and remove the rear side seatback assembly LH.

      Note

      Be careful not to damage the vehicle body.

  7. REMOVE REAR SIDE SEATBACK ASSEMBLY RH


    1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide RH.

    2. B000K82

      Remove the bolt.

    3. Disengage the hook and remove the rear side seatback assembly RH.

      Note

      Be careful not to damage the vehicle body.

  8. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Disconnect the rear door opening trim weatherstrip LH.

  9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH


    1. Disconnect the rear door opening trim weatherstrip RH.

  10. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side)


    1. B000JGT

      Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.

  11. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side)


    1. B000MY9

      Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.

  12. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH


    1. Remove the 2 nuts and child restraint seat anchor bracket sub-assembly LH.

      B000HL5E01
      Text in Illustration
      *A for Fold Down Seat Type (w/o Seat Heater System) *B for Fold Down Seat Type (w/ Seat Heater System)
      *C for Reclining Seat Type - -

  13. DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH


    1. B000JLE

      Remove the bolt and disconnect the floor anchor of the rear seat inner with center belt assembly LH.

  14. REMOVE ROOF SIDE INNER GARNISH LH


    1. B000HVV

      Disengage the 5 clips.

    2. Disengage the guide and remove the roof side inner garnish LH.

  15. REMOVE ROOF SIDE INNER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  16. REMOVE CENTER STOP LIGHT SET (w/o Rear Sunshade)


    1. B000H2KE01

      Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to disengage the 4 claws.

    2. B000IPH

      Turn the center stop light set 180 degrees as shown by the arrow in the illustration.

      Tech Tips

      This makes it easier to disconnect the connector.

    3. Disconnect the connector and remove the center stop light set.

  17. REMOVE REAR SEAT SHOULDER BELT COVER


    1. B000N9T

      Using a moulding remover, disengage the 2 claws and 4 guides and remove the rear seat shoulder belt cover.

      Tech Tips

      Use the same procedure for the other 2 rear seat shoulder belt covers.

  18. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)


    1. B000GY4E02
      Text in Illustration
      *a Protective Tape

      Using pliers, disengage the 3 clips from inside the luggage compartment as shown in the illustration.

      Tech Tips

      Tape the tips of the pliers before use.

    2. Disengage the 5 guides.

    3. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.

  19. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)


    1. B000KT1E01
      Text in Illustration
      *a Protective Tape

      Using pliers, disengage the 3 clips from inside the luggage compartment as shown in the illustration.

      Tech Tips

      Tape the tips of the pliers before use.

    2. Disengage the guide.

    3. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.

  20. REMOVE ROOM PARTITION BOARD LH


    1. B000NIU

      Disengage the guide, 2 claws and 4 clips, and remove the room partition board LH.

  21. REMOVE ROOM PARTITION BOARD RH


    1. B000HPG

      Using a clip remover, remove the 2 clips.

    2. Disengage the 5 clips, and remove the room partition board RH.

  22. REMOVE REAR SEATBACK LOCK ASSEMBLY LH (REAR SEAT LOCK CONTROL CABLE LH)


    1. B000KW8

      Disengage the hook in the order indicated in the illustration.

    2. B000LS0

      Remove the 2 nuts and rear seatback lock assembly LH (rear seat lock control cable LH).

  23. REMOVE REAR SEATBACK LOCK ASSEMBLY RH (REAR SEAT LOCK CONTROL CABLE RH)

    Tech Tips

    Use the same procedure as for the LH side.