REAR SEAT RECLINING CONTROL CABLE (for TMMK Made) INSTALLATION


  1. INSTALL REAR SEATBACK LOCK ASSEMBLY LH (REAR SEAT LOCK CONTROL CABLE LH)


    1. Install the rear seatback lock assembly LH (rear seat lock control cable LH) with the 2 nuts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    2. B000H8I

      Engage the hook as shown in the illustration.

  2. INSTALL REAR SEATBACK LOCK ASSEMBLY RH (REAR SEAT LOCK CONTROL CABLE RH)

    Tech Tips

    Use the same procedure as for the LH side.

  3. INSTALL ROOM PARTITION BOARD RH


    1. Engage the 5 clips to install the room partition board RH.

    2. Install the 2 clips.

  4. INSTALL ROOM PARTITION BOARD LH


    1. Engage the 4 clips, 2 claws and guide to install the room partition board LH.

  5. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY


    1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

    2. B000JNB

      Engage the 5 guides and 3 clips to install the package tray trim panel assembly.

  6. INSTALL REAR SEAT SHOULDER BELT COVER


    1. B000LY6

      Engage the 4 guides and 2 claws to install the rear seat shoulder belt cover.

      Tech Tips

      Use the same procedure for the other 2 rear seat shoulder belt covers.

  7. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR COVER


    1. B000ME9

      Engage the 2 guides and 2 claws to install the child restraint seat tether anchor cover.

      Tech Tips

      Use the same procedure for the other 2 child restraint seat tether anchor covers.

  8. INSTALL CENTER STOP LIGHT SET


    1. Connect the connector.

    2. Temporarily install the center stop light set.

    3. B000HQXE01

      Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to engage the 4 claws.

  9. INSTALL ROOF SIDE INNER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  10. INSTALL ROOF SIDE INNER GARNISH LH


    1. Install 5 new clips to the roof side inner garnish LH.

    2. Engage the guide.

    3. Engage the 5 clips to install the roof side inner garnish LH.

  11. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH


    1. for Type A:


      1. B000IUHE02
        Text in Illustration
        *a Protruding Part

        Connect the floor anchor of the rear seat inner with center belt assembly LH with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

        Note


        • Install the rear seat inner with center belt assembly LH with the arrow on the anchor part facing the front of the vehicle.

        • Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.

    2. for Type B:


      1. B000JA0E01
        Text in Illustration
        *a Protruding Part

        Connect the floor anchor of the rear seat inner with center belt assembly LH with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

        Note


        • Install the rear seat inner with center belt assembly LH with the arrow on the anchor part facing the front of the vehicle.

        • Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.

  12. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH


    1. Install the child restraint seat anchor bracket sub-assembly LH with the 2 nuts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  13. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side)


    1. B000HOIE02
      Text in Illustration
      *a Protruding Part

      Connect the floor anchor of the rear seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.

  14. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side)


    1. B000JWLE02
      Text in Illustration
      *a Protruding Part

      Connect the floor anchor of the rear seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.

  15. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    1. B000KSGE02
      Text in Illustration
      *a Alignment Mark (Blue)

      Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  16. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. B000JVDE02
      Text in Illustration
      *a Alignment Mark (Pink)

      Align the alignment mark (Pink) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  17. INSTALL REAR SIDE SEATBACK ASSEMBLY RH


    1. Engage the hook.

    2. Install the rear side seatback assembly RH with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    3. Connect the connector.

    4. Connect the rear seat outer belt assembly to the rear seat shoulder belt guide.

  18. INSTALL REAR SIDE SEATBACK ASSEMBLY LH


    1. Engage the hook.

    2. Install the rear side seatback assembly LH with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    3. Connect the connector.

    4. Connect the rear seat outer belt assembly to the rear seat shoulder belt guide.

  19. INSTALL REAR SEATBACK ASSEMBLY RH


    1. Place the rear seatback assembly RH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly RH with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  20. INSTALL REAR SEATBACK ASSEMBLY LH


    1. Place the rear seatback assembly LH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly LH with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  21. INSTALL INNER LUGGAGE COMPARTMENT TRIM PAD


    1. Install the inner luggage compartment trim pad.

  22. INSTALL REAR SEAT CUSHION LOCK HOOK


    1. B000HKU

      Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  23. INSTALL REAR SEAT CUSHION ASSEMBLY


    1. Place the rear seat cushion assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly.

    3. B000KWO

      Engage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly to the 2 rear seat cushion lock hooks as shown in the illustration.

    4. Confirm that the rear seat cushion assembly is securely installed.

      Note

      When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.

  24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  25. INSPECT SRS WARNING LIGHT

    Click here