REAR SEATBACK HEATER (for Reclining Seat Type) REMOVAL


  1. PRECAUTION (w/ Rear Seat Side Airbag)

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag)

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR SEAT HEADREST ASSEMBLY

  4. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. B000HUCE01

      Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.

      Standard Measurement
      a 100 mm (3.94 in.) or less

      Note

      Be sure to hold the part of the rear seat cushion assembly directly next to the rear seat cushion lock hooks when lifting it up. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.

    2. Disconnect the 2 seat heater connectors.

    3. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.

      Note

      Be careful not to damage the vehicle body.

  5. REMOVE REAR SEAT CUSHION LOCK HOOK


    1. B000LZB

      Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure as for the LH side.

  6. REMOVE REAR SEATBACK COVER


    1. B000HOH

      Disengage the 4 claws and remove the 2 rear seatback covers.

      Tech Tips

      Use the same procedure as for the LH side.

  7. REMOVE REAR SEATBACK ASSEMBLY


    1. w/ Rear Seat Side Airbag:


      1. Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly LH.

    2. Disengage the 2 rear seat belts from the 2 rear seat shoulder belt guides.

    3. B000HLQ

      Disengage the 2 hooks and disconnect the cover.

    4. Remove the 2 nuts, 2 bolts and rear seatback assembly LH.

  8. REMOVE REAR SEAT CENTER SHOULDER BELT GUIDE (for LH Side)


    1. B000MZE

      Remove the 2 screws.

    2. Disengage the guide and remove the rear seat center shoulder belt guide.

  9. REMOVE REAR SEAT SHOULDER BELT GUIDE


    1. B000IN1

      Remove the 2 screws.

    2. Disengage the guide and remove the rear seat shoulder belt guide LH.

  10. REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD


    1. B000IFX

      Disengage each hooks.

    2. Remove the 12 hog rings.

    3. w/ Rear Seat Side Airbag:


      1. B000NA6

        Remove the nut and separate the airbag bracket.

    4. B000MGT

      Disengage the 4 claws and remove the 2 rear seat headrest supports.

    5. Disengage the clamp to disconnect the seat heater wire harness from the rear seatback frame sub-assembly LH.

    6. Remove the separate type rear seatback cover with pad from the rear seatback frame sub-assembly LH.

  11. REMOVE SEPARATE TYPE REAR SEATBACK COVER (REAR SEATBACK HEATER SUB-ASSEMBLY)


    1. B000HWI

      Remove the 10 hog rings and separate type rear seatback cover (rear seatback heater sub-assembly) from the separate type rear seatback pad.