FRONT SEAT SIDE AIRBAG ASSEMBLY (for TMC, TMMR Made) INSTALLATION


  1. INSTALL FRONT SEAT AIRBAG ASSEMBLY

    CAUTION:


    • The nuts must not be reused.

    • Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.


    1. Install the front seat airbag assembly with 2 new nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    2. Engage the 2 clamps.

  2. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Manual Seat)


    1. Temporarily install the separate type front seatback cover with pad.

    2. Engage the 4 claws to install the 2 front seat headrest supports.

    3. Install the 2 brackets with the nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      CAUTION:


      • For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.

      • Make sure that the strap is not twisted after installing the nut.

      • Install the bracket securely.

    4. B000J3A

      Turn back the separate type front seatback cover.

    5. Using hog ring pliers, install the 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    6. B000J3Z

      Using hog ring pliers, install 3 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    7. B000LEG

      Using hog ring pliers, install 5 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

  3. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Power Seat)


    1. Temporarily install the separate type front seatback cover with pad.

    2. Engage the 4 claws to install the 2 front seat headrest supports.

    3. Install the 2 brackets with the nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      CAUTION:


      • For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.

      • Make sure that the strap is not twisted after installing the nut.

      • Install the bracket securely.

    4. B000J3A

      Turn back the separate type front seatback cover.

    5. Using hog ring pliers, install the 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    6. B000LVU

      Using hog ring pliers, install 3 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    7. B000N0D

      Using hog ring pliers, install 5 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

  4. CONNECT AIRBAG WIRE HARNESS (for Manual Seat)


    1. w/ Seat Heater System:


      1. Engage the clamp.

      2. Connect the connector.

    2. Engage the claw and 3 clamps to connect the airbag wire harness.

    3. Engage the fastener to install the airbag wire harness.

    4. Connect the rubber band of the separate type front seatback cover with pad.

  5. CONNECT AIRBAG WIRE HARNESS (for Power Seat)


    1. w/ Seat Heater System:


      1. Engage the clamp.

      2. Connect the connector.

    2. Engage the claw and 3 clamps to connect the airbag wire harness.

    3. Engage the fastener to install the airbag wire harness.

    4. Connect the rubber band of the separate type front seatback cover with pad.

  6. INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)

    Click here

  7. INSTALL FRONT SEAT ASSEMBLY (for Power Seat)

    Click here

  8. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here