CENTER AIRBAG SENSOR ASSEMBLY (for TMMK Made) INSTALLATION

INSTALL AIRBAG SENSOR ASSEMBLY

Check that the engine switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Using SST, install the airbag sensor assembly with the 3 bolts.

SST: 09961-00950

Text in Illustration
*1	Waterproof Sheet	-	-
*a	Torque Wrench Fulcrum Length	-	-

Torque:: Specified tightening torque; 18 N*m { 178 kgf*cm, 13 ft.*lbf }

Note

This torque value is effective when SST is parallel to a torque wrench.
If the airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
When installing the airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
When the engine switch is first turned on (IG) after the airbag sensor assembly has been replaced, make sure that no one is in the vehicle.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench Click here.
When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 250 mm (9.84 in.)): 11 N*m (112 kgf*cm, 8 ft.*lbf)

Connect the connectors to the airbag sensor assembly as shown in the illustration.

Note

When connecting any airbag connector, take care not to damage the airbag wire harness.
Check that the waterproof sheet is properly set.
Check that there is no looseness in the installation parts of the airbag sensor assembly.

INSTALL NO. 1 CONSOLE BOX DUCT
1. Install the No. 1 console box duct with the clip.
INSTALL FLOOR CARPET BRACKET LH
1. Engage the 2 guides.
2. Install the floor carpet bracket LH with the 2 clips.
INSTALL FLOOR CARPET BRACKET RH
1. Engage the 2 guides.
2. Install the floor carpet bracket RH with the 2 clips.
INSTALL FRONT NO. 2 CONSOLE BOX INSERT
1. Engage the guide and 2 clips as shown in the illustration.
2. Install the front No. 2 console box insert with the screw <C> or <D>.
3. Engage the 2 claws to connect the room temperature sensor.
INSTALL CONSOLE BOX INSERT
1. Engage the guide and 2 clips as shown in the illustration.
2. Install the console box insert with the screw <C> or <D>.
INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
1. Connect each connector.
2. Engage the guide and 2 clips as shown in the illustration.
3. Install the upper console panel sub-assembly with the 2 screws <C> or <D>.
INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
1. Connect the connector.
2. Engage the glove compartment light as shown in the illustration.
3. Engage the clamp.
4. Engage the guide and 2 clips.
5. Install the lower instrument panel sub-assembly with the 5 screws <C> or <D>.
INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY
1. Engage the 4 claws, 9 clips and 3 guides.
2. Install the lower No. 1 instrument panel finish panel assembly with the bolt <B> and screw <C> or <D>.
CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.
INSTALL INSTRUMENT SIDE PANEL LH
1. Engage the 3 guides.
2. Engage the 4 claws to install the instrument side panel LH as shown in the illustration.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
1. Engage the 2 clips.
2. Install the cowl side trim sub-assembly LH with the clip.
INSTALL FRONT DOOR SCUFF PLATE LH
1. Engage the 10 claws to install the front door scuff plate LH.
INSTALL REAR CONSOLE BOX ASSEMBLY

Click here
INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

Click here