INSIDE HANDLE LIGHT REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure described below is for the LH side.


  1. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG (for Front Door)


    1. B000H8O

      Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.

  2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH (for Front Door)


    1. B000LAY

      Disengage the 3 clips and remove the front door lower frame bracket garnish.

  3. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Door)

    for Driver Side: Click here

  4. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Door)

    for Front Passenger Side: Click here

  5. REMOVE FRONT ARMREST ASSEMBLY (for Front Door)


    1. B000N26

      Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the front armrest assembly.

  6. REMOVE COURTESY LIGHT ASSEMBLY (for Front Door)


    1. B000NPFE01
      Text in Illustration
      *A for LH Side
      *B for RH Side
      *1 Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for Front Door)


    1. B000LS6E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the front door panel.

    2. B000NJZ

      Remove the 3 screws.

    3. Using a clip remover, disengage the 10 clips.

    4. B000NQ1E01
      Text in Illustration
      *1 Reference Boss
      *2 Front Door Inner Glass Weatherstrip

      Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    5. Disengage the reference boss from the front door panel.

    6. Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.

    7. w/o Memory:


      1. Disconnect the connector.

    8. w/ Memory:


      1. Disconnect the 2 connectors.

    9. B000IDX

      Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.

  8. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY (for Front Door)


    1. B000J2V

      Disengage the 2 claws and guides, and remove the front door inside handle sub-assembly.

  9. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP (for Front Door)


    1. B000L90E01
      Text in Illustration
      *1 Screwdriver

      Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.

  10. REMOVE FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY (for Front Door)


    1. B000HUA

      Disengage the 3 clamps and claw, and remove the front door inside handle illumination light assembly.

  11. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG (for Rear Door)


    1. B000NDR

      Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.

  12. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (for Rear Door)


    1. B000I33

      Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

    2. w/o Seat Heater System:


      1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

    3. w/ Seat Heater System:


      1. Disconnect the 2 connectors and remove the rear power window regulator switch assembly with rear door armrest base panel.

  13. REMOVE REAR ARMREST ASSEMBLY (for Rear Door)


    1. B000LSK

      Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.

  14. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY (for Rear Door)


    1. B000JX3E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the rear door panel.

    2. B000I2D

      Remove the 3 screws.

    3. Using a clip remover, disengage the 8 clips.

    4. B000JHIE01
      Text in Illustration
      *1 Reference Boss
      *2 Rear Door Inner Glass Weatherstrip

      Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    5. Disengage the reference boss from the rear door panel.

    6. Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

    7. B000ITM

      Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

    8. Disconnect the connector.

    9. B000HNNE01
      Text in Illustration
      *1 Screwdriver

      Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.

  15. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY (for Rear Door)


    1. B000J2V

      Disengage the 2 claws and guide, and remove the rear door inside handle sub-assembly.

  16. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP (for Rear Door)


    1. B000ND9E01
      Text in Illustration
      *1 Screwdriver

      Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.

  17. REMOVE REAR DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY (for Rear Door)


    1. B000MD0

      Disengage the 3 clamps and claw, and remove the rear door inside handle illumination light assembly.