BLIND SPOT MONITOR SYSTEM OPERATION CHECK


  1. BLIND SPOT MONITOR BEAM AXIS INSPECTION


    1. Procedure to enter Test Mode


      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the blind spot monitor main switch (warning canceling switch assembly) on.

      4. Turn the GTS on.

      5. Switch the blind spot monitor sensor to Test Mode using the GTS. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master beam axis inspection or BSM Slave beam axis inspection.

      6. Finish Test Mode.

  2. BLIND SPOT MONITOR BEAM AXIS CONFIRMATION


    1. When performing the blind spot monitor beam axis confirmation, move the vehicle to a place where the space shown in the illustration can be secured.

      B000HKFE07

      Note


      • Perform this inspection on level ground.

      • Make sure that there are no metal objects around the vehicle or on the ground.

      • Unload the vehicle before beginning the inspection.

      • Check that the tire pressure is correct before beginning the inspection.

      • Do not place an object other than the reflector (such as a large metallic object) in or allow people to enter the inspection area (W 9 m (29.53 ft) x L 10 m (32.81 ft) x H 4 m (13.12 ft)) shown in the illustration.

      • Check that DTC C1ABB and DTC C1ABC are not output.

    2. Place the reflector.


      1. Hang a string (with weight) from the center of the vehicle's rear emblem. Mark the vehicle's rear center point on the ground. Repeat for the front of the vehicle. (mark (A) and (B))

      2. B000KGWE01

        Draw a vehicle center line so that it passes through mark (A) and (B) (front and rear center points).

      3. B000M03E14

        Mark the position on the center line 593 mm (1.94 ft.) behind the rear bumper (for LH). (Mark (C))

      4. B000IAL

        Prepare 2 pieces of string of 600 mm (1.97 ft.) in length and secure the end of each string at apoint 300 mm (11.8 in.) from mark (C) as shown in the illustration.

      5. B000H5OE01

        Pull the end of each string and mark the position where each string meets on the left side.(Mark (D))

      6. B000KLVE03

        Draw a line (P) so that it passes through mark (D) and is perpendicular to the vehicle centerline.

      7. B000M03E01

        Mark the position on the center line 589 mm (1.93 ft.) behind the rear bumper (for RH). (Mark (E))

      8. B000IALE03

        Prepare 2 pieces of string of 600 mm (1.97 ft.) in length and secure the end of each string at a point 300 mm (11.8 in.) from mark (E) as shown in the illustration.

      9. B000J7BE03

        Pull the end of each string and mark the position where each string meets on the right side.(Mark (F))

      10. B000K5NE01

        Draw a line (Q) so that it passes through mark (F) and is perpendicular to the vehicle centerline.

      11. Set the reflector at the position (Z) shown in the illustration below.

        SST
        09870-60000   ( 09870-60010 )
        09870-60040
        B000I2GE01

        Note


        • B000HHRE14

          Set the reflector so that its center is 465 mm (1.52 ft.) above the ground (for RH).

          Set the reflector so that its center is 653 mm (2.14 ft.) above the ground (for LH).

          Standard
          A
          Blind spot monitor sensor RH

          465 mm

          (1.52 ft.)
          Blind spot monitor sensor LH

          653 mm

          (2.14 ft.)
        • B000LURE01

          The center of triangular pyramid is the reference point for the setting position and angle.

        • Set the reflector as shown in the illustration so that its center of triangular pyramid faces the blind spot monitor sensor.

        • Perform the operation as precisely as possible.

    3. Perform the blind spot monitor beam axis display.


      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the blind spot monitor main switch (warning canceling switch assembly) on.

      4. Turn the GTS on.

      5. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master beam axis display or BSM Slave beam axis display.

      6. Check the results displayed for the BSM beam axis display.

        Tech Tips

        If the results are outside the allowable range, try again as the reflector setting position may be incorrect or a metal object may exist near the detection area.

      7. Perform the blind spot monitor beam axis adjustment using the GTS. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master beam axis adjustment or BSM Slave beam axis adjustment.

        Tech Tips

        When values on the axis display are in the allowable range, performing this adjustment compensates the values to the normal value.

      8. BLIND SPOT MONITOR INSTALLATION CONDITION INSPECTION

        Note


        • Perform this inspection on level ground.

        • Unload the vehicle before beginning the inspection.

        • Check that the tire pressure is correct before beginning the inspection.


        1. Remove the rear bumper Click here.

        2. Attach a jig similar to the one shown in the illustration to the outward facing surface of the blind spot monitor sensor and check that the blind spot monitor sensor is perpendicular to the floor surface or within the allowable range.

          B000KSZE01
          B000H0ME03
        9. Standard
        A B
        Blind spot monitor sensor RH

        8 mm

        (0.315 in)

        -8 mm

        (-0.315 in)
        Blind spot monitor sensor LH

        0 mm

        (0.0 in)

        -17 mm

        (-0.669 in)

    Tech Tips

    Allowable ranges A and B are different between the blind spot monitor sensor LH and RH.

  3. B000HG3E08

    Using the sensor installation stud bolt center lines as a reference, check that the stud bolts are as shown in the illustration.