NAVIGATION SYSTEM (for Navigation Receiver Type) Speaker Circuit

DESCRIPTION



WIRING DIAGRAM


  1. for TMC Made

    B000L8HE06

  2. for TMMK Made

    B000M25E01
    B000JASE18

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      for TMC Made A
      for TMMK Made B

    B

    CHECK SPEAKER (OPERATION CHECK) Click here

    A

  2. CHECK SPEAKER (OPERATION CHECK)


    1. B000MYZ

      Enter the "System Check Mode" screen.

      Refer to Check Speaker in Operation Check Click here.

    2. Perform the operation check above and determine the speaker that is not operating.

      Result
      Not Operating Speaker Proceed to
      Front No. 1 speaker assembly or front No. 2 speaker assembly A
      Rear speaker assembly B

      Tech Tips

      If sound cannot be heard from any speaker, inspect all of them.


    B

    CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY) Click here

    A

  3. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)


    1. Disconnect the I64 navigation receiver assembly connector.

    2. Disconnect the I83 and I1 front No. 2 speaker assembly connectors.

    3. Disconnect the J5 and K5 front No. 1 speaker assembly connectors.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I64-1 (FR+) - I83-4 (TWR+) Always Below 1 Ω
      I64-5 (FR-) - I83-2 (TWR-) Always Below 1 Ω
      I64-2 (FL+) - I1-4 (TWL+) Always Below 1 Ω
      I64-6 (FL-) - I1-2 (TWL-) Always Below 1 Ω
      I83-3 (+) - J5-1 Always Below 1 Ω
      I83-1 (-) - J5-2 Always Below 1 Ω
      I1-3 (+) - K5-1 Always Below 1 Ω
      I1-1 (-) - K5-2 Always Below 1 Ω
      I64-1 (FR+) or I83-4 (TWR+) - Body ground Always 10 kΩ or higher
      I64-5 (FR-) or I83-2 (TWR-) - Body ground Always 10 kΩ or higher
      I64-2 (FL+) or I1-4 (TWL+) - Body ground Always 10 kΩ or higher
      I64-6 (FL-) or I1-2 (TWL-) - Body ground Always 10 kΩ or higher
      I83-3 (+) or J5-1 - Body ground Always 10 kΩ or higher
      I83-1 (-) or J5-2 - Body ground Always 10 kΩ or higher
      I1-3 (+) or K5-1 - Body ground Always 10 kΩ or higher
      I1-1 (-) or K5-2 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly Click here.

    2. Inspect the front No. 2 speaker assembly Click here.

    3. Check that the malfunction disappears when a new or known good front No. 2 speaker assembly is installed Click here.

      OK
      Malfunction disappears.

    NG

    INSPECT FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

    END

  5. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly Click here.

    2. Inspect the front No. 1 speaker assembly Click here.


    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  6. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)


    1. Disconnect the I65 navigation receiver assembly connector.

    2. Disconnect the O18 and O21 rear speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I65-1 (RR+) - O18-1 Always Below 1 Ω
      I65-3 (RR-) - O18-2 Always Below 1 Ω
      I65-2 (RL+) - O21-1 Always Below 1 Ω
      I65-6 (RL-) - O21-2 Always Below 1 Ω
      I65-1 (RR+) or O18-1 - Body ground Always 10 kΩ or higher
      I65-3 (RR-) or O18-2 - Body ground Always 10 kΩ or higher
      I65-2 (RL+) or O21-1 - Body ground Always 10 kΩ or higher
      I65-6 (RL-) or O21-2 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly Click here.

    2. Inspect the rear speaker assembly Click here.


    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  8. CHECK SPEAKER (OPERATION CHECK)


    1. B000MYZ

      Enter the "System Check Mode" screen.

      Refer to Check Speaker in Operation Check Click here.

    2. Perform the operation check above and determine the speaker that is not operating.

      Result
      Not Operating Speaker Proceed to
      Front No. 1 speaker assembly A
      Front No. 2 speaker assembly B
      Front No. 3 speaker assembly C
      Rear No. 2 speaker assembly D
      Rear speaker assembly E

      Tech Tips

      If sound cannot be heard from any speaker, inspect all of them.


    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) Click here

    C

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) Click here

    D

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY) Click here

    E

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY) Click here

    A

  9. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)


    1. Disconnect the I68 stereo component amplifier assembly connector.

    2. Disconnect the J5 and K5 front No. 1 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I68-15 (FR+) - J5-1 (+) Always Below 1 Ω
      I68-30 (FR-) - J5-2 (-) Always Below 1 Ω
      I68-11 (FL+) - K5-1 (+) Always Below 1 Ω
      I68-26 (FL-) - K5-2 (-) Always Below 1 Ω
      I68-15 (FR+) or J5-1 (+) - Body ground Always 10 kΩ or higher
      I68-30 (FR-) or J5-2 (-) - Body ground Always 10 kΩ or higher
      I68-11 (FL+) or K5-1 (+) - Body ground Always 10 kΩ or higher
      I68-26 (FL-) or K5-2 (-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly Click here.

    2. Inspect the front No. 1 speaker assembly Click here


    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  11. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the I68 stereo component amplifier assembly connector.

    2. Disconnect the I84 and I2 front No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I68-12 (TWR+) - I84-4 Always Below 1 Ω
      I68-27 (TWR-) - I84-3 Always Below 1 Ω
      I68-14 (TWL+) - I2-4 Always Below 1 Ω
      I68-29 (TWL-) - I2-3 Always Below 1 Ω
      I68-12 (TWR+) or I84-4 - Body ground Always 10 kΩ or higher
      I68-27 (TWR-) or I84-3 - Body ground Always 10 kΩ or higher
      I68-14 (TWL+) or I2-4 - Body ground Always 10 kΩ or higher
      I68-29 (TWL-) or I2-3 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  12. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly Click here.

    2. Inspect the front No. 2 speaker assembly Click here.

    3. Check that the malfunction disappears when a new or known good front No. 2 speaker assembly is installed Click here.

      OK
      Malfunction disappears.

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    OK

    END

  13. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the I68 stereo component amplifier assembly connector.

    2. Disconnect the I60 front No. 3 speaker assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I68-13 (CTR+) - I60-2 Always Below 1 Ω
      I68-28 (CTR-) - I60-1 Always Below 1 Ω
      I68-13 (CTR+) or I60-2 - Body ground Always 10 kΩ or higher
      I68-28 (CTR-) or I60-1 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  14. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly Click here.

    2. Inspect the front No. 3 speaker assembly Click here.


    NG

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  15. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the I68 stereo component amplifier assembly connector.

    2. Disconnect the O19 and O20 rear No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I68-10 (SR+) - O19-2 Always Below 1 Ω
      I68-25 (SR-) - O19-1 Always Below 1 Ω
      I68-9 (SL+) - O20-2 Always Below 1 Ω
      I68-24 (SL-) - O20-1 Always Below 1 Ω
      I68-10 (SR+) or O19-2 - Body ground Always 10 kΩ or higher
      I68-25 (SR-) or O19-1 - Body ground Always 10 kΩ or higher
      I68-9 (SL+) or O20-2 - Body ground Always 10 kΩ or higher
      I68-24 (SL-) or O20-1 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  16. INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    1. Remove the rear No. 2 speaker assembly Click here.

    2. Inspect the rear No. 2 speaker assembly Click here.


    NG

    REPLACE REAR NO. 2 SPEAKER ASSEMBLY Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  17. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)


    1. Disconnect the I68 stereo component amplifier assembly connector.

    2. Disconnect the O22 rear speaker assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I68-8 (WF1+) - O22-1 Always Below 1 Ω
      I68-23 (WF1-) - O22-2 Always Below 1 Ω
      I68-8 (WF1+) or O22-1 - Body ground Always 10 kΩ or higher
      I68-23 (WF1-) or O22-2 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  18. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly Click here.

    2. Inspect the rear speaker assembly Click here.


    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here