NOISE FILTER (for TMC, TMMR Made) INSTALLATION


  1. INSTALL RADIO SETTING CONDENSER (for Window Defogger)


    1. B000ITX

      Engage the claw to install a new terminal cover to the wire harness.

      Note


      • Make sure to hold the wire harness so that the crimping side of the terminal is facing up when installing the wire harness to the terminal cover.

      • Make sure not to bend the exposed wire when installing the wire harness to the terminal cover.

      • Do not use excessive force when inserting the wire harness into the terminal cover.

      • If the terminal cover has been deformed at installation, replace the terminal and terminal cover with new ones.

    2. B000KY6

      Engage the 3 claws to install the new terminal cover with wire harness to a new condenser.

      Note


      • Do not use excessive force when inserting the terminal cover into the condenser.

      • If the terminal cover has been deformed at installation, replace the terminal, terminal cover and condenser with new ones.

    3. Engage the 2 clamps to temporarily install a new radio setting condenser with wire harness.

    4. Install the new radio setting condenser with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  2. INSTALL ROOF SIDE INNER GARNISH LH (for Window Defogger)


    1. Engage the guide.

    2. Engage the 5 clips to install the roof side inner garnish LH.

  3. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Window Defogger)

    for Fold Down Seat Type: Click here

  4. INSTALL RADIO SETTING CONDENSER (for High Mounted Stop Light)


    1. B000HZK

      Engage the claw to install a new terminal cover to the wire harness.

      Note


      • Make sure to hold the wire harness so that the crimping side of the terminal is facing up when installing the wire harness to the terminal cover.

      • Make sure not to bend the exposed wire when installing the wire harness to the terminal cover.

      • Do not use excessive force when inserting the wire harness into the terminal cover.

      • If the terminal cover has been deformed at installation, replace the terminal and terminal cover with new ones.

    2. B000MCI

      Engage the 6 claws to install the 2 new terminal covers with wire harness to a new condenser.

      Note


      • Do not use excessive force when inserting the terminal cover into the condenser.

      • If the terminal cover has been deformed at installation, replace the terminals, terminal covers and condenser with new ones.

    3. B000HBQ

      Engage the claw to insert the cover as shown in the illustration.

    4. Engage the clamp to temporarily install a new radio setting condenser with wire harness.

    5. Install the new radio setting condenser with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  5. INSTALL REAR SEAT SIDE GARNISH LH (for Reclining Seat Type)


    1. Engage the guide, claw and 2 clips.

    2. Install the rear seat side garnish LH with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  6. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Reclining Seat Type)


    1. B000JVDE01
      Text in Illustration
      *1 Alignment Mark (Red)

      Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  7. INSTALL REAR DOOR SCUFF PLATE LH (for Reclining Seat Type)


    1. Engage the 6 claws to install the rear door scuff plate LH.

      Tech Tips

      Engage the claws from the rear side of the scuff plate.

  8. INSTALL REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type)


    1. Place the rear seatback assembly LH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly LH with the 2 bolts and 2 nuts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    3. Engage the 2 hooks to install the cover.

    4. Connect the 2 rear seat belts to the 2 rear seat shoulder belt guides.

    5. w/ Rear Seat Side Airbag:


      1. Connect each connector and clamp to the child restraint anchor bracket sub-assembly LH.

  9. INSTALL REAR SEATBACK COVER (for Reclining Seat Type)


    1. Engage the 4 claws to install the 2 rear seatback covers.

      Tech Tips

      Use the same procedure as for the LH side.

  10. INSTALL REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type)

  11. INSTALL REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)


    1. B000HKU

      Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure as for the LH side.

  12. INSTALL REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)


    1. Place the rear seat cushion assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly.

    3. Connect the 2 seat heater connectors.

    4. B000KYT

      Engage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly to the 2 rear seat cushion lock hooks as shown in the illustration.

    5. Confirm that the rear seat cushion assembly is securely installed.

      Note

      When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.

  13. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)


    1. Place the rear side seatback assembly LH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Engage the hook to install the rear side seatback assembly LH with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    3. Connect the rear seat outer belt assembly to the rear seat shoulder belt guide LH.

  14. INSTALL REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)


    1. B000HKU

      Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure as for the LH side.

  15. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)


    1. Place the rear seat cushion assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. w/ Seat Heater System:


      1. Engage the 2 clamps.

      2. Connect the connector.

    3. B000LR0

      Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.

    4. Confirm that the rear seat cushion assembly is firmly installed.

      Note

      When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.

  16. INSTALL REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

    w/ Seat Heater System: Click here

  17. INSTALL REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

    w/ Seat Heater System: Click here

  18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  19. INSPECT SRS WARNING LIGHT (w/ Rear Seat Side Airbag)

    Click here