RADIO ANTENNA CORD (for TMC, TMMR Made) INSTALLATION


  1. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

    Tech Tips

    The double-sided tape and tape are not available as supply parts. If these pieces of tape still have enough adhesion to secure the roof headlining and antenna cord, reuse them. If the roof headlining has been replaced with a new one, or if the tape and/or the double-sided tape is no longer sticky, apply new tape following the procedure below.


    1. Apply new double-sided tape.

      B000K6XE01
      Text in Illustration
      *A w/o Sliding Roof *B w/ Sliding Roof
      *C w/ Television Antenna - -
      *a Double-sided Tape Size - -
      B000IB9 Front B000JL5 Double-sided Tape
      Double-sided Tape Size
      Area Dimension
      A 1.0 mm (0.0394 in.)
      B 10.0 mm (0.394 in.)

      1. Remove the old double-sided tape from the roof headlining assembly.

      2. Prepare the appropriate amount of new double-sided tape.

        Tech Tips

        Be careful not to touch the adhesive surface.

      3. Apply the double-sided tape to the roof headlining while aligning the tape with the markings on the roof headlining assembly.

      4. Peel off the release paper from the double-sided tape.

    2. Install the No. 2 antenna cord sub-assembly to the roof headlining assembly from the front of the vehicle.

      B000N1YE02
      Text in Illustration
      *A w/o Sliding Roof *B w/ Sliding Roof
      *C w/ Television Antenna - -
      *a Adjustment Area *b Protrusion
      B000IB9 Front B000JL5 Tape
      B000NOZ Marking Tape - -

      Tech Tips

      Align the taped part of the antenna cable with the protrusion of the roof headlining, and apply tape to secure the cable to the headlining.

    3. Put the pieces of tape back to the positions shown in the illustration in order to secure the antenna cord to the roof headlining assembly.

      Tech Tips


      • If the tape is no longer sticky, use other tape, such as packing tape, that has enough adhesion to secure the antenna cord to the roof headlining assembly.

      • For the right front corner of the roof headlining assembly, align the marking tape on the antenna cord with the protrusion of the roof headlining, and wrap tape around the antenna cord and roof headlining assembly once or twice to securely hold them.

      • For the right rear corner of the roof headlining assembly, align the marking tape on the antenna cord with the rear edge of the roof headlining, and secure the antenna cord to the roof headlining assembly with tape.

      • If the entire length of the antenna cord does not fit, adjust the length by tucking in the cord at the area shown in the illustration.

  2. INSTALL NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)

    w/ Television Antenna: Click here

  3. INSTALL ROOF HEADLINING ASSEMBLY

    Click here

  4. INSTALL ANTENNA CORD SUB-ASSEMBLY


    1. for LHD:


      1. Engage the 8 clamps to install the antenna cord sub-assembly.

    2. for RHD:


      1. Engage the 10 clamps to install the antenna cord sub-assembly.

  5. INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT


    1. B000LL0

      Engage the 2 claws.

    2. Install the No. 2 side defroster nozzle duct with the screw <D>.

  6. INSTALL NO. 3 HEATER TO REGISTER DUCT (for LHD)


    1. B000MPB

      Install the No. 3 heater to register duct with the 3 screws <D>.

    2. Install the clip.

  7. INSTALL HEATER TO REGISTER DUCT ASSEMBLY (for RHD)


    1. Engage the heater to register duct assembly to the ion generator assembly.

    2. B000IP2

      Install the heater to register duct assembly with the 3 screws <D>.

    3. Install the clip.

  8. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

    Click here