DATA LIST
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Dimmer SW | Dimmer switch high position signal/ON or OFF | ON: Dimmer switch in high or high flash position OFF: Dimmer switch in low position |
- |
| Auto Light SW | Light control switch AUTO position signal/ON or OFF | ON: Light control switch in AUTO position OFF: Light control switch not in AUTO position |
- |
| Head Light SW (Head) | Light control switch head position signal/ON or OFF | ON: Light control switch in head position OFF: Light control switch not in head position |
- |
| Illumination Rate Info | Illumination rate information/0.00 ms. to 2162.65 ms. | Value is output according to ambient light levels | - |
| Auto H Beam STS0 | Automatic high beam sensor current state/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | Undetec: Undetected CAM NA: Camera detection malfunction No sens: No detection Hlight: Oncoming vehicles with headlights on Taillgt: Preceding vehicles with taillights on Speed: Vehicle speed Daytime: Daytime state Village: Urban area Malfunc: Malfunction Delay: Standby mode Aim Lmt: Aiming misalignment SAE Mod: SAE mode Undefin: Undefined state LIN Err: LIN communication error |
| Auto H Beam STS1 | Automatic high beam sensor state past 1/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | Undetec: Undetected CAM NA: Camera detection malfunction No sens: No detection Hlight: Oncoming vehicles with headlights on Taillgt: Preceding vehicles with taillights on Speed: Vehicle speed Daytime: Daytime state Village: Urban area Malfunc: Malfunction Delay: Standby mode Aim Lmt: Aiming misalignment SAE Mod: SAE mode Undefin: Undefined state LIN Err: LIN communication error |
| Auto H Beam STS2 | Automatic high beam sensor state past 2/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | Undetec: Undetected CAM NA: Camera detection malfunction No sens: No detection Hlight: Oncoming vehicles with headlights on Taillgt: Preceding vehicles with taillights on Speed: Vehicle speed Daytime: Daytime state Village: Urban area Malfunc: Malfunction Delay: Standby mode Aim Lmt: Aiming misalignment SAE Mod: SAE mode Undefin: Undefined state LIN Err: LIN communication error |
| Auto H Beam STS3 | Automatic high beam sensor state past 3/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | Undetec: Undetected CAM NA: Camera detection malfunction No sens: No detection Hlight: Oncoming vehicles with headlights on Taillgt: Preceding vehicles with taillights on Speed: Vehicle speed Daytime: Daytime state Village: Urban area Malfunc: Malfunction Delay: Standby mode Aim Lmt: Aiming misalignment SAE Mod: SAE mode Undefin: Undefined state LIN Err: LIN communication error |
| Auto H Beam STS4 | Automatic high beam sensor state past 4/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | Undetec: Undetected CAM NA: Camera detection malfunction No sens: No detection Hlight: Oncoming vehicles with headlights on Taillgt: Preceding vehicles with taillights on Speed: Vehicle speed Daytime: Daytime state Village: Urban area Malfunc: Malfunction Delay: Standby mode Aim Lmt: Aiming misalignment SAE Mod: SAE mode Undefin: Undefined state LIN Err: LIN communication error |
| Auto H Beam STS5 | Automatic high beam sensor state past 5/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | Undetec: Undetected CAM NA: Camera detection malfunction No sens: No detection Hlight: Oncoming vehicles with headlights on Taillgt: Preceding vehicles with taillights on Speed: Vehicle speed Daytime: Daytime state Village: Urban area Malfunc: Malfunction Delay: Standby mode Aim Lmt: Aiming misalignment SAE Mod: SAE mode Undefin: Undefined state LIN Err: LIN communication error |
| Auto H Beam STS6 | Automatic high beam sensor state past 6/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | Undetec: Undetected CAM NA: Camera detection malfunction No sens: No detection Hlight: Oncoming vehicles with headlights on Taillgt: Preceding vehicles with taillights on Speed: Vehicle speed Daytime: Daytime state Village: Urban area Malfunc: Malfunction Delay: Standby mode Aim Lmt: Aiming misalignment SAE Mod: SAE mode Undefin: Undefined state LIN Err: LIN communication error |
| Auto H Beam STS7 | Automatic high beam sensor state past 7/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | Undetec: Undetected CAM NA: Camera detection malfunction No sens: No detection Hlight: Oncoming vehicles with headlights on Taillgt: Preceding vehicles with taillights on Speed: Vehicle speed Daytime: Daytime state Village: Urban area Malfunc: Malfunction Delay: Standby mode Aim Lmt: Aiming misalignment SAE Mod: SAE mode Undefin: Undefined state LIN Err: LIN communication error |
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / Automatic High Beam / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Automatic High Beam Operation | Automatic high beam system operation | ON/OFF | ON: Operation start OFF: Operation stop |