RADIATOR REMOVAL


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work Click here.

  2. DRAIN ENGINE COOLANT

    Note

    Do not remove the radiator cap sub-assembly, cylinder block drain cock plugs and radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


    1. Loosen the radiator drain cock plug.

    2. Loosen the cylinder block drain cock plug (for Bank 1).

    3. Loosen the cylinder block drain cock plug (for Bank 2, w/ Cylinder Block Drain Cock Plug).

    4. Remove the radiator cap sub-assembly.

      B000J0SE02
      Text in Illustration
      *1 Radiator Cap Sub-assembly *2 Cylinder Block Drain Cock Plug (for Bank 1)
      *3 Cylinder Block Drain Cock Plug (for Bank 2, w/ Cylinder Block Drain Cock Plug) *4 Radiator Drain Cock Plug
      *5 Air Drain Cock Plug - -

      Tech Tips

      Collect the engine coolant in a container and dispose of it according to the regulations in your area.

  3. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

  4. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

  5. REMOVE ENGINE UNDER COVER RH

  6. REMOVE ENGINE UNDER COVER LH

  7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  8. REMOVE BATTERY


    1. B000JQD

      Disconnect the positive (+) cable from the positive (+) battery terminal.

    2. Loosen the nut and remove the bolt.

    3. Remove the battery and battery tray.

  9. REMOVE FRONT BUMPER ASSEMBLY

    Click here

  10. REMOVE INLET NO. 2 AIR CLEANER


    1. B000NQO

      Disconnect the 2 wire harness clamps and vacuum hose clamp.

    2. Remove the 2 bolts and inlet No. 2 air cleaner.

  11. REMOVE INLET NO. 1 AIR CLEANER


    1. B000IUB

      Disengage the pin and remove the inlet No. 1 air cleaner.

  12. REMOVE RADIATOR RESERVE TANK ASSEMBLY


    1. B000LC1

      Disconnect the radiator reserve tank hose.

    2. Remove the 2 bolts and radiator reserve tank assembly.

  13. DISCONNECT NO. 1 RADIATOR HOSE


    1. B000MV7

      Disconnect the No. 1 radiator hose.

  14. DISCONNECT NO. 2 RADIATOR HOSE


    1. B000KV8

      Disconnect the No. 2 radiator hose and clamp.

  15. DISCONNECT INLET NO. 1 OIL COOLER HOSE


    1. B000I7M

      Disconnect the inlet No. 1 oil cooler hose.

  16. DISCONNECT OUTLET NO. 1 OIL COOLER HOSE


    1. B000KJI

      Disconnect the outlet No. 1 oil cooler hose.

  17. REMOVE HOOD LOCK ASSEMBLY


    1. B000K66E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the hood lock nut cap.

      Tech Tips

      Tape the screwdriver tip before use.

    2. B000L2M

      Disconnect the connector.

    3. B000H1RE01
      Text in Illustration
      *1 Hood Lock Bolt

      Remove the 2 bolts and hood lock bolt.

    4. B000H3Y

      Disconnect the hood lock control cable assembly and remove the hood lock assembly.

  18. REMOVE UPPER RADIATOR SUPPORT


    1. B000IYB

      Disconnect the 2 connectors.

    2. B000IGO

      Disconnect the hood lock control cable clamp and remove the 5 bolts and upper radiator support.

    3. Remove the 2 radiator support cushions from the radiator assembly.

  19. REMOVE RADIATOR ASSEMBLY


    1. B000M9X

      Disconnect the 3 clamps and connector.

    2. B000INN

      Remove the 4 bolts and separate the condenser assembly from the radiator assembly.

    3. B000LGH

      Remove the radiator assembly with fan assembly.

      Note

      Do not apply any excessive force to the cooler condenser assembly or pipe when removing the radiator assembly.

    4. Remove the 2 lower radiator supports from the radiator assembly.

    5. B000I0C

      Release the 3 claws and lift the fan assembly from the radiator.