ENGINE SWITCH REMOVAL


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Manual Tilt and Manual Telescopic Steering Column)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Power Tilt and Power Telescopic Steering Column)


    1. Disable the auto away/return function by changing the customize parameter Click here.

      Note

      Record the current customize parameter setting (whether the auto away/return function is enabled or disabled) in order to restore the current setting after finishing this operation.

      Tech Tips

      Performing the above operation disables the auto away/return function when the engine switch is turned off.

    2. Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.

    3. Turn the engine switch off and disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for LHD)

    for TMC, TMMR Made: Click here

    for TMMK Made: Click here

  5. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for LHD)

    for TMC, TMMR Made: Click here

    for TMMK Made: Click here

  6. REMOVE FRONT DOOR SCUFF PLATE LH (for LHD)


    1. B000I9QE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.

      Tech Tips

      Make the front pillar garnish LH hang down from the front pillar garnish clip.

    2. B000HANE01

      While pushing the tabs on the front pillar garnish clip in the direction indicated by the arrow (A) shown in the illustration, disengage the front pillar garnish clip.

    3. Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.

    4. B000KY7E01
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  7. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for LHD)


    1. B000MCM

      Remove the clip.

    2. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  8. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for LHD)


    1. B000HXQ

      Disconnect the front door opening trim weatherstrip LH.

  9. REMOVE INSTRUMENT SIDE PANEL LH (for LHD)


    1. B000HH8

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. B000MY7

      Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.

  10. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY (for LHD)


    1. B000J4N

      Disengage the 4 clips to remove the No. 1 instrument panel register assembly as shown in the illustration.

  11. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for LHD)

    for TMC, TMMR Made: Click here

    for TMMK Made: Click here

  12. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for LHD)


    1. B000H4N

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  13. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)

    for TMC, TMMR Made: Click here

    for TMMK Made: Click here

  14. REMOVE FRONT ASH RECEPTACLE ASSEMBLY (for LHD)


    1. B000I30

      Remove the 2 screws <C>.

    2. B000HWD

      Disengage the 2 clips as shown in the illustration.

    3. Disconnect each connector to remove the front ash receptacle assembly.

  15. REMOVE CONSOLE BOX ASSEMBLY (for LHD)

    Click here.

  16. REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for LHD)


    1. for LHD:


      1. B000MWF

        Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.

    2. B000HGW

      Remove the 2 screws <C>.

    3. B000HQ9

      Disengage the clip and 4 guides to remove the front No. 2 console box insert as shown in the illustration.

  17. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for LHD)


    1. B000LT8

      Disengage the 3 clips and guide to remove the lower instrument panel finish panel assembly.

    2. for LHD with Smart Entry and Start System:


      1. Disconnect the connector.

  18. REMOVE ENGINE SWITCH (for LHD)


    1. B000HRF

      Disengage the 2 claws and remove the engine switch.

  19. REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)

    Tech Tips

    Use the same procedure as for the LH side.

  20. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH (for RHD)

    Tech Tips

    Use the same procedure as for the LH side Click here.

  21. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for RHD)


    1. B000J7V

      Disconnect the front door opening trim weatherstrip RH.

  22. REMOVE INSTRUMENT SIDE PANEL RH (for RHD)


    1. B000LEU

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. B000JRJ

      Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.

  23. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL (for RHD)


    1. B000H9B

      Disengage the 2 claws and 4 clips to remove the upper instrument panel finish panel as shown in the illustration.

    2. w/ Smart Entry and Start System:


      1. Disconnect the connector.

  24. REMOVE ENGINE SWITCH (for RHD)


    1. B000MRH

      Disengage the 2 claws and remove the engine switch.