REAR SUSPENSION MEMBER (for TMC, TMMR Made) REMOVAL

REMOVE REAR WHEELS
REMOVE CENTER EXHAUST PIPE ASSEMBLY
- for 2AR-FE: Click here
- for 6AR-FSE: Click here
- for 2GR-FE: Click here

REMOVE NO. 2 FLOOR UNDER COVER

for TMC Made:

Remove the screw and 2 clips.

Text in Illustration
	Nut (attached to under cover)
	Screw

Disengage the 6 nuts and remove the No. 2 floor under cover.

Tech Tips

The 6 nuts will remain attached to the No. 2 floor under cover.

for TMMR Made:
1. Remove the 2 clips.
  
  Text in Illustration
  
  Nut (attached to under cover)
2. Disengage the 6 nuts and remove the No. 2 floor under cover.
  
  Tech Tips
  
  The 6 nuts will remain attached to the No. 2 floor under cover.

REMOVE NO. 1 FLOOR UNDER COVER

for TMC Made:

Remove the screw.

Text in Illustration
	Nut (attached to under cover)
	Screw

Disengage the 5 nuts and 2 clips, and remove the No. 1 floor under cover.

Tech Tips

Rotate the clips to disengage them. The 5 nuts and 2 clips will remain attached to the No. 1 floor under cover.

for TMMR Made:
1. Disengage the 5 nuts and 2 clips, and remove the No. 1 floor under cover.
  
  Text in Illustration
  
  Nut (attached to under cover)
  
  Tech Tips
  
  Rotate the clips to disengage them. The 5 nuts and 2 clips will remain attached to the No. 1 floor under cover.

SEPARATE REAR STABILIZER LINK ASSEMBLY LH
1. Remove the nut and separate the rear stabilizer link assembly LH from the rear stabilizer bar.
  
  If the ball joint turns together with the nut, use a hexagon wrench to hold the stud.
SEPARATE REAR STABILIZER LINK ASSEMBLY RH

Tech Tips

Perform the same procedure as for the LH side.
REMOVE REAR STABILIZER BAR
1. Remove the 4 bolts, rear stabilizer bar, 2 rear No. 1 stabilizer bar brackets and 2 rear stabilizer bushings.
REMOVE NO. 3 EXHAUST PIPE SUPPORT BRACKET
1. Remove the 2 bolts and No. 3 exhaust pipe support bracket from the rear suspension member sub-assembly.
REMOVE REAR BODY END MOUNTING BRACKET SUB-ASSEMBLY
1. Remove the 2 bolts and rear body end mounting bracket sub-assembly from the rear suspension member sub-assembly.
REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)

Click here
SEPARATE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
1. Remove the bolt, nut and separate the rear No. 2 suspension arm assembly (outer side) from the rear axle carrier sub-assembly.
  
  Note
  
  When removing the bolt, keep the nut from rotating.
SEPARATE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

Tech Tips

Perform the same procedure as for the LH side.
SEPARATE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
1. Remove the bolt, nut and separate the rear No. 1 suspension arm assembly (outer side) from the rear axle carrier sub-assembly.
  
  Note
  
  When removing the bolt, keep the nut from rotating.
SEPARATE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

Tech Tips

Perform the same procedure as for the LH side.

REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

Text in Illustration
*1	Engine Lifter
*2	Attachment
	Attachment Placement Location

Support the rear suspension member sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

Note

Make sure to secure the rear suspension member sub-assembly to prevent it from dropping.
Use the attachments to keep the rear suspension member sub-assembly level.

Remove the 2 bolts, 4 nuts, 2 rear suspension member lower stopper sub-assemblies and 2 rear suspension member lower stoppers.
Slowly lower the rear suspension member sub-assembly.

Note

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.

REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
1. Remove the bolt and rear No. 2 suspension arm assembly LH from the rear suspension member sub-assembly.
REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

Tech Tips

Perform the same procedure as for the LH side.
REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
1. Remove the bolt and rear No. 1 suspension arm assembly from the rear suspension member sub-assembly.
REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

Tech Tips

Perform the same procedure as for the LH side.
REMOVE REAR SUSPENSION MEMBER DAMPER (w/ Dynamic Damper)
1. Remove the 2 bolts and rear suspension member damper from the rear suspension member sub-assembly.
REMOVE REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION LH
1. Using SST and a press, remove the rear suspension member body mounting front cushion LH from the rear suspension member sub-assembly.
  
  SST
  
  09527-17011
  
  09950-60010 ( 09951-00320 )
  
  09950-70010 ( 09951-07100 )
REMOVE REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION RH

Tech Tips

Perform the same procedure as the LH side.
REMOVE REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for LH Side)
1. Using SST and a press, remove the rear suspension member body mounting rear cushion from the rear suspension member sub-assembly.
  
  SST
  
  09527-17011
  
  09950-60010 ( 09951-00320 )
  
  09950-70010 ( 09951-07100 )
REMOVE REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for RH Side)

Tech Tips

Perform the same procedure as the LH side.
REMOVE HOLE PLUG
1. Remove the 3 hole plugs from the rear suspension member sub-assembly.
  
  Tech Tips
  
  There are 2 sizes of the hole plugs.