REAR SUSPENSION MEMBER (for TMMK Made) REMOVAL


  1. REMOVE REAR WHEELS

  2. REMOVE CENTER EXHAUST PIPE ASSEMBLY

    Click here

  3. REMOVE NO. 2 FLOOR UNDER COVER


    1. B000LIZ

      Remove the 2 bolts, screw and 2 clips.

      Text in Illustration
      B000K70 Bolt
      B000IB9 Screw
      B000JQI Nut (attached to under cover)

    2. Disengage the 3 nuts and remove the No. 2 floor under cover.

  4. REMOVE NO. 1 FLOOR UNDER COVER


    1. B000KYG

      Remove the 2 bolts and screw.

      Text in Illustration
      B000K70 Bolt
      B000IB9 Screw
      B000JQI Nut (attached to under cover)

    2. Disengage the 3 nuts and 2 clips, and remove the No. 1 floor under cover.

  5. SEPARATE REAR STABILIZER LINK ASSEMBLY LH


    1. B000JLC

      Remove the nut and separate the rear stabilizer link assembly LH from the rear stabilizer bar.

      If the ball joint turns together with the nut, use a hexagon wrench to hold the stud.

  6. SEPARATE REAR STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  7. REMOVE REAR STABILIZER BAR


    1. B000JQJ

      Remove the 4 nuts, rear stabilizer bar, 2 rear No. 1 stabilizer bar brackets, 2 rear No. 2 stabilizer bar brackets and 2 rear stabilizer bushings from the rear suspension member sub-assembly.

  8. REMOVE NO. 3 EXHAUST PIPE SUPPORT BRACKET


    1. B000KYA

      Remove the 2 bolts and No. 3 exhaust pipe support bracket from the rear suspension member sub-assembly.

  9. REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

    Click here

  10. SEPARATE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. B000KTX

      Remove the bolt, nut and separate the rear No. 2 suspension arm assembly (outer side) from the rear axle carrier sub-assembly.

      Note

      When removing the bolt, keep the nut from rotating.

  11. SEPARATE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  12. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. B000IWK

      Remove the bolt and rear No. 2 suspension arm assembly from the rear suspension member sub-assembly.

  13. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  14. SEPARATE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    1. B000L0E

      Remove the bolt, nut and separate the rear No. 1 suspension arm assembly (outer side) from the rear axle carrier sub-assembly.

      Note

      When removing the bolt, keep the nut from rotating.

  15. SEPARATE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  16. REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY


    1. B000LXFE01
      Text in Illustration
      *1 Engine Lifter
      *2 Attachment
      B000JL5 Attachment Placement Location

      Support the rear suspension member sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

      Note


      • Make sure to secure the rear suspension member sub-assembly to prevent it from dropping.

      • Use the attachments to keep the rear suspension member sub-assembly level.

    2. Remove the 2 bolts, 4 nuts, 2 rear suspension member lower stopper sub-assemblies and 2 rear suspension member lower stoppers.

      B000I8I

    3. Slowly lower the rear suspension member sub-assembly.

      Note

      When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.

    4. Remove the 2 differential support member cushions and 2 differential support member upper stoppers from the rear suspension member sub-assembly.

  17. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    1. B000MBF

      Remove the bolt and rear No. 1 suspension arm assembly from the rear suspension member sub-assembly.

  18. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  19. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION LH


    1. B000MYBE01

      Using SST and a press, remove the rear suspension member body mounting front cushion LH from the rear suspension member sub-assembly.

      SST
      09527-17011
      09950-60010   ( 09951-00340 )
      09950-70010   ( 09951-07100 )

  20. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION RH

    Tech Tips

    Perform the same procedure as the LH side.

  21. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for LH Side)


    1. B000IGBE01

      Using SST and a press, remove the rear suspension member body mounting rear cushion from the rear suspension member sub-assembly.

      SST
      09527-17011
      09950-60010   ( 09951-00340 )
      09950-70010   ( 09951-07100 )

  22. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for RH Side)

    Tech Tips

    Perform the same procedure as the LH side.

  23. REMOVE HOLE PLUG


    1. B000HYP

      Remove the 4 hole plugs from the rear suspension member sub-assembly.