REAR BUMPER(for Wagon) REASSEMBLY

PROCEDURE

1. INSTALL REAR BUMPER ARM SUB-ASSEMBLY LH

   
   

   1. 

      Install the rear bumper arm sub-assembly LH with the 3 bolts.

      Torque:

      11.5 N*m  { 117 kgf*cm, 8 ft.*lbf }

2. INSTALL REAR BUMPER ARM SUB-ASSEMBLY RH

   Tech Tips

   Use the same procedure as for the LH side.

3. INSTALL NO. 1 REAR BUMPER REINFORCEMENT

   
   

   1. 

      Install the No. 1 rear bumper reinforcement with the 8 bolts.

      Torque:

      11.5 N*m  { 117 kgf*cm, 8 ft.*lbf }

4. INSTALL REAR BUMPER SIDE SEAL LH

   
   

   1. 

      Install the rear bumper side seal LH with the 3 clips.

5. INSTALL REAR BUMPER SIDE SEAL RH

   
   

   1. 

      Install the rear bumper side seal RH with the 3 clips.

6. INSTALL UPPER REAR BUMPER RETAINER LH

   
   

   1. 

      Engage the 2 guides to temporarily install the upper rear bumper retainer LH to the rear combination light assembly LH.

   2. 

      Engage the 2 guides as shown in the illustration to temporarily install the upper rear bumper retainer LH and rear combination light assembly LH as a set.

   3. Install the upper rear bumper retainer LH with the screw.

7. INSTALL UPPER REAR BUMPER RETAINER RH

   Tech Tips

   Use the same procedure as for the LH side.

8. INSTALL REAR COMBINATION LIGHT ASSEMBLY LH

   Click here

9. INSTALL REAR COMBINATION LIGHT ASSEMBLY RH

   Tech Tips

   Use the same procedure as for the LH side.

10. INSTALL REAR BUMPER SIDE RETAINER LH

    
    

    1. 

       Engage the guide and 4 claws.

    2. 

       Install the rear bumper side retainer LH with the 3 screws.

11. INSTALL REAR BUMPER SIDE RETAINER RH

    Tech Tips

    Use the same procedure as for the LH side.

12. INSTALL NO. 2 REAR BUMPER MOULDING

    
    

    1. 

       Engage the 10 claws.

    2. Install the No. 2 rear bumper moulding to the rear bumper guard with the 2 screws.

    3. 

       Engage the guide and 10 claws.

    4. 

       Install the rear bumper guard with No. 2 rear bumper moulding with the 2 clips.

13. INSTALL REFLEX REFLECTOR ASSEMBLY LH

    
    

    1. 

       Engage the guide.

    2. Engage the claw.

    3. Install the reflex reflector assembly LH with the screw.

    4. 

       Engage the 6 claws to install the rear bumper extension LH.

14. INSTALL REFLEX REFLECTOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

15. INSTALL REAR BUMPER PAD LH

    
    

    1. Clean the rear bumper assembly.

       
       

       1. Remove any remaining double-sided tape from the rear bumper assembly.

       2. Wipe off any tape adhesive residue with cleaner.

    2. Remove the release paper from a new rear bumper pad LH.

       Tech Tips

       After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. 

       *a

       Line

       Install the rear bumper pad LH as shown in the illustration.

       Tech Tips

       Install the rear bumper pad LH along the line marked on the rear bumper assembly.

16. INSTALL REAR BUMPER PAD RH

    Tech Tips

    Use the same procedure as for the LH side.

17. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

    Click here

18. INSTALL NO. 3 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

    Click here

19. INSTALL NO. 3 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

    Click here

20. INSTALL NO. 2 LUGGAGE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)

    
    

    1. Engage the 4 clamps.

       

       *a	Line	-	-
       	Adhesive Tape	-	-

    2. Connect the 4 connectors.

    3. Install the No. 2 luggage room wire to the rear bumper assembly with adhesive tape as shown in the illustration.

       Note

       
       

       • Apply the tape securely in place.

       • Do not touch the adhesive surface when applying the tape to prevent adhesion failure.