DATA LIST
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / AFS / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| AFS OFF Switch | AFS OFF switch signal | ON or OFF | ON: Headlight swivel main switch pushed OFF: Headlight swivel main switch not pushed |
- |
| Traveling Direction | Traveling Direction | Not Fwd or Fwd | Not Fwd: Shift lever in R or N*1 Fwd: Shift lever not in R or N*1 |
- |
| Headlight Low Beam State | Low beam headlight state | ON or OFF | ON: Low beam headlights on OFF: Low beam headlights off |
- |
| Headlight High Beam State | High beam headlight state | ON or OFF | ON: High beam headlights on OFF: High beam headlights off |
- |
| DRL State | State of the DRL | ON or OFF | ON: DRL operating OFF: DRL not operating |
- |
| Engine | Engine condition | Run or Stop | Run: Engine running Stop: Engine stopped |
- |
| +B | IG power supply voltage value | 0.00 to 19.75 V | 11.00 to 14.00 V | - |
| Height Sens Pw Supply Val | Height control sensor power supply value | 0.00 to 6.25 V | 4.70 to 5.20 V | - |
| Rr Height Sens Signal Val | Rear height control sensor signal value | 0.00 to 5.00 V | 0.50 to 4.50 V | Value changes according to vehicle height |
| Steering Sens Signal | Steering angle sensor signal value | -384.0 deg to 382.5 deg | Approx. 0 deg (When steering wheel is straight) | Value changes according to steering wheel position |
| Steering Sens Center Pos | Steering angle sensor center position | -3072.0 deg to 3070.5 deg | Condition can be displayed | - |
| FR Wheel Speed | Front right wheel speed | 0.00 to 327.67 km/h (203.61 mph) | Condition can be displayed | - |
| FL Wheel Speed | Front left wheel speed | 0.00 to 327.67 km/h (203.61 mph) | Condition can be displayed | - |
| Vehicle Speed | Vehicle speed | 0.00 to 327.67 km/h (203.61 mph) | Condition can be displayed | - |
| Rear Height Adjust Valid Flag | Rear height adjustment range | Valid or Invalid | Condition can be displayed | - |
| Init Writing Count | Number of times for initialization | 0 to 255 | Condition can be displayed | - |
| Sensor Initialization Hist | Sensor Initialization History | not comp, 10%, 25%, 50%, 75%, 100% or complied | Condition can be displayed | - |
| L Swivel Target Step | Swivel motor LH target step value | 0 to 400 step | 47 to 248 step | - |
| L Swivel Current Step | Swivel motor LH current step value | 0 to 400 step | 47 to 248 step | - |
| R Swivel Target Step | Swivel motor RH target step value | 0 to 400 step | 22 to 198 step | - |
| R Swivel Current Step | Swivel motor RH current step value | 0 to 400 step | 22 to 198 step | - |
| LR Leveling Target Step | Swivel motor LH and RH target step value | 0 to 300 step | 14 to 362 step | - |
| L Leveling Current Step | Swivel motor LH current step value | 0 to 300 step | 14 to 362 step | - |
| R Leveling Current Step | Swivel motor RH current step value | 0 to 300 step | 14 to 362 step | - |
| Number Of Trouble Codes | Number of trouble codes | 0 to 255 | Condition can be displayed | - |
*1: for CVT or Multi-mode Manual Transaxle
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / AFS / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Drive The Leveling Motor | Swivel motor upward or downward operation | Stop/Down/Up | Perform the active test with the engine started and vehicle stopped. |
| Drive Swivel Motor LH LEFT | Swivel motor LH left direction rotation | ON/OFF | Perform the active test with the engine started and vehicle stopped. |
| Drive Swivel Motor LH RIGHT | Swivel motor LH right direction rotation | ON/OFF | Perform the active test with the engine started and vehicle stopped. |
| Drive Swivel Motor RH LEFT | Swivel motor RH left direction rotation | ON/OFF | Perform the active test with the engine started and vehicle stopped. |
| Drive Swivel Motor RH RIGHT | Swivel motor RH right direction rotation | ON/OFF | Perform the active test with the engine started and vehicle stopped. |
| AFS OFF Indicator | AFS OFF indicator | ON/OFF | - |