POWER WINDOW REGULATOR MOTOR(for Sedan Front Side) INSPECTION

PROCEDURE

1. INSPECT FRONT DOOR WINDOW REGULATOR ASSEMBLY LH (w/ Jam Protection Function)

   CAUTION:

   Prevent any part of your body from being caught during inspection.

   
   
   1. 

      *a	Component without harness connected (Front Door Window Regulator Assembly LH)
      *b	Up
      *c	Down

      Apply positive (+) battery voltage to connector terminal 2 (B).

      Note

      Do not apply positive (+) battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

   2. Connect a negative (-) battery to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

   3. Check that window regulator moves smoothly as follows:

      OK

      Measurement Condition Specified Condition Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP). Disconnect and reconnect the negative (-) battery lead for terminal 10 (UP) within 1 second. Arm of window regulator rotates clockwise (Up) Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN). Disconnect and reconnect the negative (-) battery lead for terminal 7 (DOWN) within 1 second. Arm of window regulator rotates counterclockwise (Down)

      
      

      • If the result is not as specified, replace the front door window regulator assembly LH.

      Note

      Initialize the power window control system after installing the front door window regulator assembly LH.

2. INSPECT FRONT DOOR WINDOW REGULATOR ASSEMBLY LH (w/o Jam Protection Function)

   CAUTION:

   Prevent any part of your body from being caught during inspection.

   
   
   1. 

      *a	Component without harness connected (Front Door Window Regulator Assembly LH)
      *b	Up
      *c	Down

      Apply battery voltage to the motor connector according to the table below.

      Note

      Do not apply battery voltage to any terminals except terminals 1 and 2.

      Standard
      Measurement Condition Specified Condition Battery positive (+) → Terminal 2 Battery negative (-) → Terminal 1 Arm of window regulator rotates clockwise (Up) Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 2 Arm of window regulator rotates counterclockwise (Down)

      If the result is not as specified, replace the front door window regulator assembly LH.

3. INSPECT FRONT DOOR WINDOW REGULATOR ASSEMBLY RH (w/ Jam Protection Function)

   CAUTION:

   Prevent any part of your body from being caught during inspection.

   
   
   1. 

      *a	Component without harness connected (Front Door Window Regulator Assembly RH)
      *b	Up
      *c	Down

      Apply positive (+) battery voltage to connector terminal 2 (B).

      Note

      Do not apply positive (+) battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

   2. Connect a negative (-) battery to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

   3. Check that window regulator moves smoothly as follows:

      OK

      Measurement Condition Specified Condition Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP). Disconnect and reconnect the negative (-) battery lead for terminal 10 (UP) within 1 second. Arm of window regulator rotates counterclockwise (Up) Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN). Disconnect and reconnect the negative (-) battery lead for terminal 7 (DOWN) within 1 second. Arm of window regulator rotates clockwise (Down)

      
      

      • If the result is not as specified, replace the front door window regulator assembly RH.

      Note

      Initialize the power window control system after installing the front door window regulator assembly RH.

4. INSPECT FRONT DOOR WINDOW REGULATOR ASSEMBLY RH (w/o Jam Protection Function)

   CAUTION:

   Prevent any part of your body from being caught during inspection.

   
   
   1. 

      *a	Component without harness connected (Front Door Window Regulator Assembly RH)
      *b	Up
      *c	Down

      Apply battery voltage to the motor connector according to the table below.

      Note

      Do not apply battery voltage to any terminals except terminals 1 and 2.

      Standard
      Measurement Condition Specified Condition Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 2 Arm of window regulator rotates clockwise (Down) Battery positive (+) → Terminal 2 Battery negative (-) → Terminal 1 Arm of window regulator rotates counterclockwise (Up)

      If the result is not as specified, replace the front door window regulator assembly RH.