POWER WINDOW MASTER SWITCH INSPECTION

PROCEDURE

1. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Models with Jam Protection Function on 4 Windows)

   
   
   1. 

      *a	Component without harness connected (Power Window Regulator Master Switch Assembly)
      *b	LED

      Check that the LEDs illuminate.

      
      

      1. Apply battery voltage to the power window regulator master switch assembly and check that the LEDs illuminate.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 18 (LED) Battery negative (-) → 12 (GND) LEDs illuminate

         If the result is not as specified, replace the power window regulator master switch assembly.

2. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for LHD) (for Models with Jam Protection Function on Driver Door Window Only)

   
   
   1. 

      *a	Component without harness connected (Power Window Regulator Master Switch Assembly (w/ Rear Power Window))

      Check the switch function. (w/ Rear Power Window)

      
      

      1. Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Driver Side Switch Tester Connection Condition Specified Condition 4 (A) - 1 (E) AUTO UP Below 1 Ω 8 (U) - 1 (E) AUTO UP Below 1 Ω 8 (U) - 1 (E) MANUAL UP Below 1 Ω 5 (D) - 1 (E) MANUAL DOWN Below 1 Ω 4 (A) - 1 (E) AUTO DOWN Below 1 Ω 5 (D) - 1 (E) AUTO DOWN Below 1 Ω

         Standard Resistance
         Front Passenger Side Switch Tester Connection Condition Specified Condition 6 (B) - 16 (U) UP Below 1 Ω 1 (E) - 15 (D) UP Below 1 Ω 1 (E) - 16 (U) Off Below 1 Ω 1 (E) - 15 (D) Off Below 1 Ω 1 (E) - 16 (U) DOWN Below 1 Ω 6 (B) - 15 (D) DOWN Below 1 Ω

         Standard Resistance
         Rear RH Side Switch Tester Connection Condition Specified Condition 6 (B) - 10 (U) UP Below 1 Ω 1 (E) - 18 (D) UP Below 1 Ω 1 (E) - 18 (D) Off Below 1 Ω 1 (E) - 10 (U) Off Below 1 Ω 6 (B) - 18 (D) DOWN Below 1 Ω 1 (E) - 10 (U) DOWN Below 1 Ω

         Standard Resistance
         Rear LH Side Switch Tester Connection Condition Specified Condition 6 (B) - 12 (U) UP Below 1 Ω 1 (E) - 13 (D) UP Below 1 Ω 1 (E) - 13 (D) Off Below 1 Ω 1 (E) - 12 (U) Off Below 1 Ω 6 (B) - 13 (D) DOWN Below 1 Ω 1 (E) - 12 (U) DOWN Below 1 Ω

         If the result is not as specified, replace the power window regulator master switch assembly.

   2. 

      *a	Component without harness connected (Power Window Regulator Master Switch Assembly (w/o Rear Power Window))

      Check the switch function. (w/o Rear Power Window)

      
      

      1. Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Driver Side Switch Tester Connection Condition Specified Condition 1 (A) - 7 (E) AUTO UP Below 1 Ω 18 (U) - 7 (E) AUTO UP Below 1 Ω 18 (U) - 7 (E) MANUAL UP Below 1 Ω 10 (D) - 7 (E) MANUAL DOWN Below 1 Ω 1 (A) - 7 (E) AUTO DOWN Below 1 Ω 10 (D) - 7 (E) AUTO DOWN Below 1 Ω

         Standard Resistance
         Front Passenger Side Switch Tester Connection Condition Specified Condition 15 (B) - 12 (U) UP Below 1 Ω 7 (E) - 16 (D) UP Below 1 Ω 7 (E) - 12 (U) Off Below 1 Ω 7 (E) - 16 (D) Off Below 1 Ω 7 (E) - 12 (U) DOWN Below 1 Ω 15 (B) - 16 (D) DOWN Below 1 Ω

         If the result is not as specified, replace the power window regulator master switch assembly.

   3. 

      *a	Component without harness connected (Power Window Regulator Master Switch Assembly (w/ Rear Power Window))

      Check that the LEDs illuminate. (w/ Rear Power Window)

      
      

      1. Apply battery voltage to the power window regulator master switch assembly and check that the LEDs illuminate.

         OK
         Measurement Condition Specified Condition Battery positive (+) → Terminal 3 (LED) Battery negative (-) → Terminal 1 (E) LEDs illuminate

         If the result is not as specified, replace the power window regulator master switch assembly.

   4. 

      *a	Component without harness connected (Power Window Regulator Master Switch Assembly (w/o Rear Power Window))

      Check that the LEDs illuminate. (w/o Rear Power Window)

      
      

      1. Apply battery voltage to the power window regulator master switch assembly and check that the LEDs illuminate.

         OK
         Measurement Condition Specified Condition Battery positive (+) → Terminal 6 (LED) Battery negative (-) → Terminal 7 (E) LEDs illuminate

         If the result is not as specified, replace the power window regulator master switch assembly.

   5. 

      *a	Component with harness connected (Power Window Regulator Master Switch Assembly)

      Check the switch function. (w/ Rear Power Window)

      
      

      1. Reconnect the power window regulator master switch assembly.

      2. Measure the voltage according to the value(s) in the table below.

         Standard Voltage

         Tester Connection Condition Specified Condition 8 (U) - 1 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V 8 (U) - 1 (E) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V 8 (U) - 1 (E) Ignition switch ON, driver door power window regulator switch up (Manual operation) Below 1 V 4 (A) - 1 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V 4 (A) - 1 (E) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V 4 (A) - 1 (E) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V 5 (D) - 1 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V 5 (D) - 1 (E) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V 5 (D) - 1 (E) Ignition switch ON, driver door power window regulator switch down (Manual operation) Below 1 V

         If the result is not as specified, replace the power window regulator master switch assembly.

   6. 

      *a	Component with harness connected (Power Window Regulator Master Switch Assembly)

      Check the switch function. (w/o Rear Power Window)

      
      

      1. Reconnect the power window regulator master switch assembly.

      2. Measure the voltage according to the value(s) in the table below.

         Standard Voltage

         Tester Connection Condition Specified Condition 18 (U) - 7 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V 18 (U) - 7 (E) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V 18 (U) - 7 (E) Ignition switch ON, driver door power window regulator switch up (Manual operation) Below 1 V 1 (A) - 7 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V 1 (A) - 7 (E) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V 1 (A) - 7 (E) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V 10 (D) - 7 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V 10 (D) - 7 (E) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V 10 (D) - 7 (E) Ignition switch ON, driver door power window regulator switch down (Manual operation) Below 1 V

         If the result is not as specified, replace the power window regulator master switch assembly.

3. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for RHD) (for Models with Jam Protection Function on Driver Door Window Only)

   
   
   1. 

      *a	Component without harness connected (Power Window Regulator Master Switch Assembly (w/ Rear Power Window))

      Check the switch function. (w/ Rear Power Window)

      
      

      1. Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Driver Side Switch Tester Connection Condition Specified Condition 4 (A) - 9 (E) AUTO UP Below 1 Ω 1 (U) - 9 (E) AUTO UP Below 1 Ω 1 (U) - 9 (E) MANUAL UP Below 1 Ω 5 (D) - 9 (E) MANUAL DOWN Below 1 Ω 4 (A) - 9 (E) AUTO DOWN Below 1 Ω 5 (D) - 9 (E) AUTO DOWN Below 1 Ω

         Standard Resistance
         Front Passenger Side Switch Tester Connection Condition Specified Condition 6 (B) - 12 (U) UP Below 1 Ω 9 (E) - 13 (D) UP Below 1 Ω 9 (E) - 12 (U) Off Below 1 Ω 9 (E) - 13 (D) Off Below 1 Ω 9 (E) - 12 (U) DOWN Below 1 Ω 6 (B) - 13 (D) DOWN Below 1 Ω

         Standard Resistance
         Rear RH Side Switch Tester Connection Condition Specified Condition 6 (B) - 16 (U) UP Below 1 Ω 9 (E) - 15 (D) UP Below 1 Ω 9 (E) - 15 (D) Off Below 1 Ω 9 (E) - 16 (U) Off Below 1 Ω 6 (B) - 15 (D) DOWN Below 1 Ω 9 (E) - 16 (U) DOWN Below 1 Ω

         Standard Resistance
         Rear LH Side Switch Tester Connection Condition Specified Condition 6 (B) - 18 (U) UP Below 1 Ω 9 (E) - 10 (D) UP Below 1 Ω 9 (E) - 10 (D) Off Below 1 Ω 9 (E) - 18 (U) Off Below 1 Ω 6 (B) - 10 (D) DOWN Below 1 Ω 9 (E) - 18 (U) DOWN Below 1 Ω

         If the result is not as specified, replace the power window regulator master switch assembly.

   2. 

      *a	Component without harness connected (Power Window Regulator Master Switch Assembly (w/o Rear Power Window))

      Check the switch function. (w/o Rear Power Window)

      
      

      1. Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Driver Side Switch Tester Connection Condition Specified Condition 18 (A) - 7 (E) AUTO UP Below 1 Ω 9 (U) - 7 (E) AUTO UP Below 1 Ω 9 (U) - 7 (E) MANUAL UP Below 1 Ω 6 (D) - 7 (E) MANUAL DOWN Below 1 Ω 18 (A) - 7 (E) AUTO DOWN Below 1 Ω 6 (D) - 7 (E) AUTO DOWN Below 1 Ω

         Standard Resistance
         Front Passenger Side Switch Tester Connection Condition Specified Condition 15 (B) - 12 (U) UP Below 1 Ω 7 (E) - 10 (D) UP Below 1 Ω 7 (E) - 12 (U) Off Below 1 Ω 7 (E) - 10 (D) Off Below 1 Ω 7 (E) - 12 (U) DOWN Below 1 Ω 15 (B) - 10 (D) DOWN Below 1 Ω

         If the result is not as specified, replace the power window regulator master switch assembly.

   3. 

      *a	Component without harness connected (Power Window Regulator Master Switch Assembly (w/ Rear Power Window))

      Check that the LEDs illuminate. (w/ Rear Power Window)

      
      

      1. Apply battery voltage to the power window regulator master switch assembly and check that the LEDs illuminate.

         OK
         Measurement Condition Specified Condition Battery positive (+) → Terminal 3 (LED) Battery negative (-) → Terminal 9 (E) LEDs illuminate

         If the result is not as specified, replace the power window regulator master switch assembly.

   4. 

      *a	Component without harness connected (Power Window Regulator Master Switch Assembly (w/o Rear Power Window))

      Check that the LEDs illuminate. (w/o Rear Power Window)

      
      

      1. Apply battery voltage to the power window regulator master switch assembly and check that the LEDs illuminate.

         OK
         Measurement Condition Specified Condition Battery positive (+) → Terminal 16 (LED) Battery negative (-) → Terminal 7 (E) LEDs illuminate

         If the result is not as specified, replace the power window regulator master switch assembly.

   5. 

      *a	Component with harness connected (Power Window Regulator Master Switch Assembly)

      Check the switch function. (w/ Rear Power Window)

      
      

      1. Reconnect the power window regulator master switch assembly.

      2. Measure the voltage according to the value(s) in the table below.

         Standard Voltage

         Tester Connection Condition Specified Condition 1 (U) - 9 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V 1 (U) - 9 (E) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V 1 (U) - 9 (E) Ignition switch ON, driver door power window regulator switch up (Manual operation) Below 1 V 4 (A) - 9 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V 4 (A) - 9 (E) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V 4 (A) - 9 (E) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V 5 (D) - 9 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V 5 (D) - 9 (E) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V 5 (D) - 9 (E) Ignition switch ON, driver door power window regulator switch down (Manual operation) Below 1 V

         If the result is not as specified, replace the power window regulator master switch assembly.

   6. 

      *a	Component with harness connected (Power Window Regulator Master Switch Assembly)

      Check the switch function. (w/o Rear Power Window)

      
      

      1. Reconnect the power window regulator master switch assembly.

      2. Measure the voltage according to the value(s) in the table below.

         Standard Voltage

         Tester Connection Condition Specified Condition 9 (U) - 7 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V 9 (U) - 7 (E) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V 9 (U) - 7 (E) Ignition switch ON, driver door power window regulator switch up (Manual operation) Below 1 V 18 (A) - 7 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V 18 (A) - 7 (E) Ignition switch ON, driver door power window regulator switch up (Auto up position) Below 1 V 18 (A) - 7 (E) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V 6 (D) - 7 (E) Ignition switch ON, driver door power window regulator switch off 11 to 14 V 6 (D) - 7 (E) Ignition switch ON, driver door power window regulator switch down (Auto down position) Below 1 V 6 (D) - 7 (E) Ignition switch ON, driver door power window regulator switch down (Manual operation) Below 1 V

         If the result is not as specified, replace the power window regulator master switch assembly.