POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Driver Door Window Only) Rear Power Window LH does not Operate with Rear Power Window Switch LH

DESCRIPTION

When the ignition switch is ON, the rear door window regulator assembly (for LH door) is operated by the rear power window regulator switch assembly (for LH door).

WIRING DIAGRAM

A012LNTE15

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • Check that the window lock switch is off before performing the following procedure.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR) - BATTERY)


    1. Disconnect the K5 rear power window regulator switch assembly (for LH door) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      K5-3 (B) - Body ground Ignition switch ON 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR)


    1. A012GJOC02
      *a

      Component without harness connected

      (Rear Power Window Regulator Switch Assembly (for LH Door))

      Remove the rear power window regulator switch assembly (for LH door).

      Click here

    2. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (D) - 2 (SD) UP Below 1 Ω
      3 (B) - 4 (U) Below 1 Ω
      1 (D) - 2 (SD) Off Below 1 Ω
      4 (U) - 5 (SU) Below 1 Ω
      4 (U) - 5 (SU) DOWN Below 1 Ω
      1 (D) - 3 (B) Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR) - REAR DOOR WINDOW REGULATOR ASSEMBLY (FOR LH DOOR))


    1. Disconnect the K6 rear door window regulator assembly (for LH door) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K5-4 (U) - K6-1 (U) Always Below 1 Ω
      K5-1 (D) - K6-2 (D) Always Below 1 Ω
      K5-4 (U) - Body ground Always 10 kΩ or higher
      K5-1 (D) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    1. A012F22C14
      *A for LHD
      *B for RHD
      *a

      Component without harness connected

      (Power Window Regulator Master Switch Assembly)

      Remove the power window regulator master switch assembly.

      Click here

    2. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      6 (B) - 12 (U) UP Below 1 Ω
      1 (E) - 13 (D) Below 1 Ω
      1 (E) - 12 (U) Off Below 1 Ω
      1 (E) - 13 (D) Below 1 Ω
      6 (B) - 13 (D) DOWN Below 1 Ω
      1 (E) - 12 (U) Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      6 (B) - 18 (U) UP Below 1 Ω
      9 (E) - 10 (D) Below 1 Ω
      9 (E) - 18 (U) Off Below 1 Ω
      9 (E) - 10 (D) Below 1 Ω
      6 (B) - 10 (D) DOWN Below 1 Ω
      9 (E) - 18 (U) Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR))


    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      H11-12 (U) - K5-5 (SU) Always Below 1 Ω
      H11-13 (D) - K5-2 (SD) Always Below 1 Ω
      H11-12 (U) - Body ground Always 10 kΩ or higher
      H11-13 (D) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      G11-18 (U) - K5-5 (SU) Always Below 1 Ω
      G11-10 (D) - K5-2 (SD) Always Below 1 Ω
      G11-18 (U) - Body ground Always 10 kΩ or higher
      G11-10 (D) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR DOOR WINDOW REGULATOR ASSEMBLY (FOR LH DOOR) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR