LOWER INSTRUMENT PANEL(for Hatchback, Wagon) REMOVAL

PROCEDURE


  1. PRECAUTION

    Click here

  2. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

    Click here

  3. REMOVE CONSOLE BOX ASSEMBLY

    Click here

  4. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  5. REMOVE COWL SIDE TRIM BOARD LH

    Click here

  6. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for LHD)


    1. A012K9Z

      Disengage the 8 clips.

    2. Disconnect each connector and remove the lower instrument cluster finish panel assembly.

  7. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for RHD)


    1. w/o Entry and Start System:


      1. A012KTB

        Disengage the claw and 6 clips.

      2. Disconnect each connector and remove the lower instrument cluster finish panel assembly.

    2. w/ Entry and Start System:


      1. A012K10

        Disengage the 8 clips.

      2. Disconnect each connector and remove the lower instrument cluster finish panel assembly.

  8. REMOVE NO. 2 SWITCH HOLE BASE (for LHD)


    1. A012H90

      Disengage the 3 clips and remove the No. 2 switch hole base as shown in the illustration.

  9. REMOVE NO. 2 SWITCH HOLE BASE (for RHD)


    1. w/o Entry and Start System:


      1. A012MW9

        Disengage the 5 clips and remove the No. 2 switch hole base as shown in the illustration.

    2. w/ Entry and Start System:


      1. A012MKC

        Disengage the 4 clips as shown in the illustration.

      2. Disconnect the connector and remove the No. 2 switch hole base.

  10. REMOVE NO. 1 SWITCH HOLE BASE (for LHD)


    1. w/o Entry and Start System:


      1. A012KPC

        Disengage the 4 clips and remove the No. 1 switch hole base.

    2. w/ Entry and Start System:


      1. A012HSH

        Disengage the 4 clips as shown in the illustration.

      2. Disconnect the connector and remove the No. 1 switch hole base.

  11. REMOVE NO. 1 SWITCH HOLE BASE (for RHD)


    1. A012FF8

      Disengage the 4 clips as shown in the illustration.

    2. Disconnect the connector and remove the No. 1 switch hole base.

  12. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Instrument Panel Under Cover)


    1. A012KIG

      Remove the 2 screws <E>.

    2. A012JQ8

      Disengage the claw and guide, and remove the No. 1 instrument panel under cover sub-assembly.

  13. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)


    1. A012MSW

      Disengage the 7 clips and remove the lower instrument panel finish panel sub-assembly.

  14. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

    Click here

  15. REMOVE STEREO OPENING COVER WITH BRACKET (w/o Radio Receiver)


    1. A012F8P

      Remove the 4 bolts <B>.

    2. Disengage the 2 guides.

    3. Disconnect the connector and remove the stereo opening cover with bracket.

  16. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)

    Click here

  17. REMOVE NO. 1 NAVIGATION ANTENNA CORD SUB-ASSEMBLY (w/ Navigation System)

    Click here

  18. REMOVE AIR CONDITIONING CONTROL ASSEMBLY

    Click here

  19. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL


    1. A012M1U

      Disengage the 2 clips and 3 guides as shown in the illustration.

    2. Disengage the clamp.

    3. Disconnect each connector and remove the lower center instrument panel finish panel.

  20. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  21. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure as for the LH side.

  22. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Instrument Panel Under Cover)


    1. A012GMP

      Disengage the 3 claws and guide and remove the No. 2 instrument panel under cover sub-assembly.

  23. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. A012IB3C01
      *1 Glove Compartment Door Stopper Sub-assembly
      *a Stopper

      Disengage the claw and release the glove compartment door stopper sub-assembly.

    2. Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and pull the glove compartment door assembly until the stoppers are released.

    3. A012L20C01
      *a Close
      *b Open approximately 53°

      Open the glove compartment door assembly to approximately 53° from its closed position. Pull it horizontally in the direction indicated by the arrow to disengage the 2 hinges and remove the glove compartment door assembly.

      Note

      Pulling the glove compartment door assembly upward to remove it causes the hinges to deform. Be sure to pull out the glove compartment door assembly horizontally.

  24. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY


    1. A012M82

      Disengage the claw and remove the glove compartment door stopper sub-assembly.

  25. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A012LCF

      Disengage the claw and 2 guides and disconnect the hood lock control lever sub-assembly.

  26. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Disengage each clamp.

      A012JZ5C01
      *1 Room Temperature Sensor (Cooler Thermistor) - -
      *a DLC3 - -

    2. Disconnect each connector.

    3. Disengage the 2 claws and disconnect the DLC3.

    4. for Automatic Air Conditioning System:


      1. Disengage the 2 claws and disconnect the room temperature sensor (cooler thermistor).

    5. Remove the 2 bolts <A>, 8 screws <C>, screw <D> and lower instrument panel sub-assembly.

      A012LBQC02
      *a Bolt <A> *b Screw <C>
      *c Screw <D> - -