LOWER INSTRUMENT PANEL(for Sedan) REMOVAL

PROCEDURE


  1. PRECAUTION

    Click here

  2. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

    Click here

  3. REMOVE CONSOLE BOX ASSEMBLY

    Click here

  4. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  5. REMOVE COWL SIDE TRIM BOARD LH

    Click here

  6. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for LHD)


    1. A0030K0

      Disengage the 8 clips.

    2. Disconnect each connector and remove the lower instrument cluster finish panel assembly.

  7. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for RHD)


    1. A0030N8

      Disengage the claw and 6 clips.

    2. Disconnect each connector and remove the lower instrument cluster finish panel assembly.

  8. REMOVE NO. 2 SWITCH HOLE BASE (for LHD)


    1. A0030OG

      Disengage the 3 clips and remove the No. 2 switch hole base as shown in the illustration.

  9. REMOVE NO. 2 SWITCH HOLE BASE (for RHD)


    1. A0030C8

      Disengage the 5 clips and remove the No. 2 switch hole base as shown in the illustration.

  10. REMOVE NO. 1 SWITCH HOLE BASE (for LHD)


    1. w/o Entry and Start System:


      1. A0030HG

        Disengage the 4 clips and remove the No. 1 switch hole base as shown in the illustration.

    2. w/ Entry and Start System:


      1. A002ZVT

        Disengage the 4 clips as shown in the illustration.

      2. Disconnect the connector and remove the No. 1 switch hole base.

  11. REMOVE NO. 1 SWITCH HOLE BASE (for RHD)


    1. A00309S

      Disengage the 4 clips as shown in the illustration.

    2. Disconnect the connector and remove the No. 1 switch hole base.

  12. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A002ZV3

      Remove the 2 screws <G>.

    2. A002ZVE

      Disengage the claw and guide, and remove the No. 1 instrument panel under cover sub-assembly.

  13. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)


    1. A0030Y1

      Disengage the 7 clips and remove the lower instrument panel finish panel sub-assembly.

  14. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY WITH DOOR (w/ Knee Airbag)

    Click here

  15. REMOVE STEREO OPENING COVER WITH BRACKET (w/o Radio Receiver)


    1. A00315Z

      Remove the 4 bolts <C>.

    2. Disengage the 2 guides.

    3. Disconnect the connector and remove the stereo opening cover with bracket.

  16. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)

    Click here

  17. REMOVE NO. 1 NAVIGATION ANTENNA CORD SUB-ASSEMBLY (w/ Navigation System)

    Click here

  18. REMOVE AIR CONDITIONING PANEL ASSEMBLY (for Manual Air Conditioning System)

    Click here

  19. REMOVE CENTER INSTRUMENT PANEL SAFETY PAD RETAINER WITH AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

    Click here

  20. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  21. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure as for the LH side.

  22. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A0030I0

      Disengage the 3 claws and guide and remove the No. 2 instrument panel under cover sub-assembly.

  23. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. A002ZUZC01
      *1 Glove Compartment Door Stopper Sub-assembly
      *a Stopper

      Disengage the claw to disconnect the glove compartment door stopper sub-assembly.

    2. Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and pull down the glove compartment door assembly until the stoppers are released.

    3. A00301DC01
      *a Closed
      *b Open Approximately 53°

      Open the glove compartment door assembly to approximately 53° from its closed position. Pull it horizontally in the direction indicated by the arrow to disengage the 2 hinges and remove the glove compartment door assembly.

      Note

      Pulling the glove compartment door assembly upward to remove it causes the hinges to deform. Be sure to pull out the glove compartment door assembly horizontally.

  24. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY


    1. A0030FY

      Disengage the claw and remove the glove compartment door stopper sub-assembly.

  25. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A002ZP3

      Disengage the claw and 2 guides and disconnect the hood lock control lever sub-assembly.

  26. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Disengage each clamp.

      A0030GFC01
      *A for Automatic Air Conditioning System - -
      *1 Cooler (Room Temp. Sensor) Thermistor - -
      *a DLC3 - -

    2. Disconnect each connector.

    3. Disengage the 2 claws and disconnect the DLC3.

    4. for Automatic Air Conditioning System:


      1. Disengage the 2 claws and disconnect the cooler (room temp. sensor) thermistor.

    5. Remove the 2 bolts <A> or <B>, 8 screws <D>, screw <E> or <F> and lower instrument panel sub-assembly.

      A0030M4C01
      *a Bolt <A> or <B> *b Screw <D>
      *c Screw <E> or <F> - -