THEFT DETERRENT SYSTEM SYSTEM DESCRIPTION


  1. OUTLINE OF THEFT DETERRENT SYSTEM


    • The theft deterrent system can be set/canceled by locking/unlocking the doors using the following operation:


      • Entry lock operation

      • Wireless lock operation

        Tech Tips

        w/ Entry and Start System w/o Entry and Start System
        Entry lock operation ○ -
        Wireless lock operation ○ ○

        • ○: Available

        • -: Not available

    • The alarm function will be activated when someone attempts to forcibly unlock any of the doors or open any of the doors, engine hood and back door while the system is in the armed state.

    • In the alarm sounding state, the system blinks the hazard warning lights. At the same time, the system sounds the vehicle horn and security horn to deter break-in and theft as well as to warn people around the vehicle.

    • The theft deterrent system has the active arming mode. There are 4 states; a disarmed state, an arming preparation state, an armed state and an alarm sounding state.


    1. Disarmed state:


      • The alarm function is not operating.

      • The theft deterrent system is not operating.

    2. Arming preparation state:


      • The time until the system goes into the armed state.

      • The theft deterrent system is not operating.

    3. Armed state:


      • The theft deterrent system is operating.

    4. Alarm sounding state:


      • The alarm function is operating.

      Alarm Methods and Time
      Alarm Method Hazard Warning Lights Blinking
      Vehicle Horn

      Sounding

      (approx. 0.4-second cycles)
      Security Horn

      Sounding

      (approx. 0.4-second cycles)
      Alarm Time Approx. 27.5 seconds

  • FUNCTION OF MAIN COMPONENTS

    Component Function
    Security indicator light Informs driver of theft deterrent system status.
    Security horn Sounds when attempted break-in or theft is detected.
    Hazard warning lights Blink when attempted break-in or theft is detected.
    Vehicle horn Sounds when attempted break-in or theft is detected.
    Door courtesy light switch Detects door status (open or closed).
    Door unlock detection switch Detects door status (locked or unlocked).
    Engine hood courtesy switch Detects engine hood status (open or closed).
    Back door courtesy light switch Detects back door status (open or closed).
    Certification ECU (smart key ECU assembly)*1

    • Receives wireless door lock/unlock signal.

    • Receives entry door lock/unlock signal.
    Main body ECU (multiplex network body ECU)*2 Receives wireless door lock/unlock signal.

  • ACTIVE ARMING MODE


    1. Active arming mode:

      This system operates as described in the diagram below when one of the items for each condition is met.

      Tech Tips

      The term "all doors" used in this section refers to the driver door, front passenger door, rear door LH, rear door RH and back door.

      A012HUAE13
      w/ Entry and Start System
      Condition Item
      Condition [1]

      In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met:


      • With all doors and the engine hood closed, all doors are locked by wireless operation or the entry and start system.
      Condition [2]

      • Allow approx. 30 seconds to elapse.
      Condition [3]

      • All doors are unlocked by wireless operation or the entry and start system.

      • Any door is unlocked.

      • Any door is opened.

      • The engine switch is pushed.

      • The ignition switch is turned to ACC or ON.

      • The battery is reconnected.
      Condition [4]

      • The engine hood is opened when the engine hood is closed.

      • The battery is reconnected.

      • Any door is opened when all doors are closed.

      • Any door is unlocked when all doors are locked.

      • When 5 seconds or more have elapsed after the engine switch is pressed, the power source mode is changed from off to on (IG) without pressing the engine switch.

      • The engine hood is open.

      • Any door is unlocked.

      • Any door is opened

      • The power source mode is on (IG).
      Condition [5]

      • The ignition switch is turned to ON and the engine is running for more than 2 seconds.

      • All doors are unlocked by wireless operation or the entry and start system.
      Condition [6]

      • After approx. 27.5 seconds, alarm stops and 5 seconds later system returns to armed state.
      Condition [7]

      • The engine hood is closed when the engine hood is opened.
      Condition [8]

      • Any door is unlocked when all doors are locked.

      • Any door is opened.

      • The engine switch is pushed.

      • The ignition switch is turned to ACC or ON.

      • The battery is reconnected.

      • All doors are unlocked by wireless operation or the entry and start system.
      Condition [9]

      In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met:


      • With all doors closed and the engine hood opened, all doors are locked by wireless operation or the entry and start system.
      Condition [10]

      • The engine hood is opened.
      w/o Entry and Start System
      Condition Item
      Condition [1]

      In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met when the key is not in the key cylinder:


      • With all doors and the engine hood closed, all doors are locked by wireless operation.
      Condition [2]

      • Allow approx. 30 seconds to elapse.
      Condition [3]

      • All doors are unlocked by wireless operation.

      • Any door is unlocked.

      • Any door is opened.

      • Key is in the key cylinder.

      • The ignition switch is turned to ACC or ON.

      • The battery is reconnected.
      Condition [4]

      • The engine hood is opened when the engine hood is closed.

      • The battery is reconnected.

      • Any door is opened when all doors are closed.

      • Any door is unlocked when all doors are locked.

      • The ignition switch is turned to ON when the key is not in the key cylinder.

      • The engine hood is open.

      • Any door is unlocked.

      • Any door is opened

      • The ignition switch is ON when the key is not in the key cylinder.
      Condition [5]

      • The ignition switch is turned to ON and the engine is running for more than 2 seconds.

      • All doors are unlocked by wireless operation.
      Condition [6]

      • After approx. 27.5 seconds, alarm stops and 5 seconds later system returns to armed state.
      Condition [7]

      • The engine hood is closed when the engine hood is opened.
      Condition [8]

      • Any door is unlocked when all doors are locked.

      • Any door is opened.

      • Key is in the key cylinder.

      • The ignition switch is turned to ACC or ON.

      • The battery is reconnected.

      • All doors are unlocked by wireless operation.
      Condition [9]

      In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met when the key is not in the key cylinder:


      • With all doors closed, and the engine hood opened, all doors are locked by wireless operation.
      Condition [10]

      • The engine hood is opened.

  • FORCED DOOR LOCK CONTROL


    1. The forced door lock control prevents the vehicle from being tampered with. Immediately after a door is unlocked (armed starts), all doors are forced to lock by a forced door lock signal.


      1. If the following conditions are met, the forced door lock control is operated.


        • The key is not in the key cylinder.*

        • The theft deterrent system is in the armed state.

        • Any door is unlocked.


        • *: w/o Entry and Start System

  • SECURITY INDICATOR LIGHT OUTPUT

    Tech Tips

    When the immobiliser system is set, the security indicator light blinks during both the disarmed state and the armed state, due to output signals from the immobiliser system.


    1. According to the state of the theft deterrent system, the main body ECU (multiplex network body ECU) outputs a signal to turn the security indicator light on. However, some of the actual lighting conditions of the security indicator light are different from the output signals of the main body ECU (multiplex network body ECU).

      Output
      State of Theft Deterrent System Security Indicator Light
      Output Signal from Main Body ECU (Multiplex Network Body ECU) Actual Lighting Condition
      Disarmed state (1), (2) OFF

      OFF (Immobiliser system unset)

      BLINKING (Immobiliser system set)
      Arming preparation state ON ON
      Armed state OFF BLINKING
      Alarm sounding state ON ON
      Blinking Cycle
      Time Security Indicator Light
      0.125 sec. ON
      1.875 sec. OFF