NAVIGATION SYSTEM, Diagnostic DTC:B15C3

DTC Code DTC Name
B15C3 Speaker Output Short

DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C3 Speaker Output Short A short is detected in the speaker output circuit

  • Harness or connector

  • Speaker

  • Radio and display receiver assembly*1

  • Stereo component amplifier assembly*2

  • Telematics transceiver*3

WIRING DIAGRAM


  1. for 6 Speakers

    A01TBNIE04

  2. for 9 Speakers

    A01TCXXE01
    A01T9OAE04
    *a Rear Speaker Assembly RH
    *b Rear Speaker Assembly LH
    *c No. 1 Speaker with Box Assembly
    *d Stereo Component Amplifier Assembly

PROCEDURE


  1. CONFIRM MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      for 6 Speakers (w/o Manual (SOS) Switch) A
      for 6 Speakers (w/ Manual (SOS) Switch) B
      for 9 Speakers C

    B

    CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY, TELEMATICS TRANSCEIVER OR SPEAKERS - BODY GROUND) Click here

    C

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND) Click here

    A

  2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY OR SPEAKERS - BODY GROUND)


    1. Disconnect the E1 and E2 radio and display receiver assembly connectors.

    2. Disconnect the G4 and H5 front No. 2 speaker assembly connectors.

    3. Disconnect the L79 and L80 rear speaker assembly connectors (for Sedan).

      Disconnect the J2 and K2 rear speaker assembly connectors (for Hatchback, Wagon).

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G4-4 (TWR+) or E1-1 (FR+) - Body ground Always 10 kΩ or higher
      G4-2 (TWR-) or E1-5 (FR-) - Body ground Always 10 kΩ or higher
      H5-4 (TWL+) or E1-2 (FL+) - Body ground Always 10 kΩ or higher
      H5-2 (TWL-) or E1-6 (FL-) - Body ground Always 10 kΩ or higher
      L79-1 or E2-1 (RR+) - Body ground*1 Always 10 kΩ or higher
      L79-2 or E2-3 (RR-) - Body ground*1 Always 10 kΩ or higher
      L80-1 or E2-2 (RL+) - Body ground*1 Always 10 kΩ or higher
      L80-2 or E2-6 (RL-) - Body ground*1 Always 10 kΩ or higher
      J2-1 or E2-1 (RR+) - Body ground*2 Always 10 kΩ or higher
      J2-2 or E2-3 (RR-) - Body ground*2 Always 10 kΩ or higher
      K2-1 or E2-2 (RL+) - Body ground*2 Always 10 kΩ or higher
      K2-2 or E2-6 (RL-) - Body ground*2 Always 10 kΩ or higher

      • *1: for Sedan

        *2: for Hatchback, Wagon

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY OR FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND)


    1. Disconnect the G1 and H1 front No. 1 speaker assembly connectors.

    2. Disconnect the G4 and H5 front No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G4-3 (+) or G1-1 - Body ground Always 10 kΩ or higher
      G4-1 (-) or G1-2 - Body ground Always 10 kΩ or higher
      H5-3 (+) or H1-1 - Body ground Always 10 kΩ or higher
      H5-1 (-) or H1-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      for Sedan: Click here

      for Hatchback, Wagon: Click here

    2. A01T9OZC30
      *a

      Component without harness connected

      (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 3.2 to 4.8 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY for Sedan: Click here
    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY for Hatchback, Wagon: Click here

    OK

  5. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      for Sedan: Click here

      for Hatchback, Wagon: Click here

    2. A01TAH2C11
      *A for RH
      *B for LH
      *a

      Component without harness connected

      (Front No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for RH)
      Tester Connection Condition Specified Condition
      4 (TWR+) - 2 (TWR-) Always 10 kΩ or higher
      3 (+) - 4 (TWR+) Always Below 1 Ω
      1 (-) - 2 (TWR-) Always Below 1 Ω
      Standard Resistance (for LH)
      Tester Connection Condition Specified Condition
      4 (TWL+) - 2 (TWL-) Always 10 kΩ or higher
      3 (+) - 4 (TWL+) Always Below 1 Ω
      1 (-) - 2 (TWL-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY for Sedan: Click here
    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY for Hatchback, Wagon: Click here

    OK

  6. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Replace the front No. 2 speaker assembly with a new or known good one.

      for Sedan: Click here

      for Hatchback, Wagon: Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.

      Tech Tips


      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both the LH and RH side.

      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  7. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      for Sedan: Click here

      for Hatchback, Wagon: Click here

    2. A01T9OZC30
      *a

      Component without harness connected

      (Rear Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 3.2 to 4.8 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY for Sedan: Click here
    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY for Hatchback, Wagon: Click here

    NG

    REPLACE REAR SPEAKER ASSEMBLY for Sedan: Click here
    REPLACE REAR SPEAKER ASSEMBLY for Hatchback, Wagon: Click here

  8. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY, TELEMATICS TRANSCEIVER OR SPEAKERS - BODY GROUND)


    1. Disconnect the E1 and E2 radio and display receiver assembly connectors.

    2. Disconnect the E143 telematics transceiver connector.

    3. Disconnect the H5 front No. 2 speaker assembly LH connector.

    4. Disconnect the L79 and L80 rear speaker assembly connectors.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E1-1 (FR+) or E143-2 (SPI+) - Body ground Always 10 kΩ or higher
      E1-5 (FR-) or E143-3 (SPI-) - Body ground Always 10 kΩ or higher
      E1-2 (FL+) or H5-4 (TWL+) - Body ground Always 10 kΩ or higher
      E1-6 (FL-) or H5-2 (TWL-) - Body ground Always 10 kΩ or higher
      E2-1 (RR+) or L79-1 - Body ground Always 10 kΩ or higher
      E2-3 (RR-) or L79-2 - Body ground Always 10 kΩ or higher
      E2-2 (RL+) or L80-1 - Body ground Always 10 kΩ or higher
      E2-6 (RL-) or L80-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. INSPECT TELEMATICS TRANSCEIVER


    1. Remove the telematics transceiver.

      Click here

    2. A01TA0IC05
      *a

      Component without harness connected

      (Telematics Transceiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) or 5 (SPO+) - Body ground Always 10 kΩ or higher
      3 (SPI-) or 6 (SPO-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE TELEMATICS TRANSCEIVER Click here

    OK

  10. CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY RH OR TELEMATICS TRANSCEIVER - BODY GROUND)


    1. Disconnect the G4 front No. 2 speaker assembly RH connector.

    2. Disconnect the E143 telematics transceiver connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G4-4 (TWR+) or E143-5 (SPO+) - Body ground Always 10 kΩ or higher
      G4-2 (TWR-) or E143-6 (SPO-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY OR FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND)


    1. Disconnect the G1 and H1 front No. 1 speaker assembly connectors.

    2. Disconnect the G4 and H5 front No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G4-3 (+) or G1-1 - Body ground Always 10 kΩ or higher
      G4-1 (-) or G1-2 - Body ground Always 10 kΩ or higher
      H5-3 (+) or H1-1 - Body ground Always 10 kΩ or higher
      H5-1 (-) or H1-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  12. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. A01T9OZC30
      *a

      Component without harness connected

      (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 3.2 to 4.8 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  13. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. A01TAH2C11
      *A for RH
      *B for LH
      *a

      Component without harness connected

      (Front No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      4 (TWR+) - 2 (TWR-) Always 10 kΩ or higher
      3 (+) - 4 (TWR+) Always Below 1 Ω
      1 (-) - 2 (TWR-) Always Below 1 Ω
      4 (TWL+) - 2 (TWL-) Always 10 kΩ or higher
      3 (+) - 4 (TWL+) Always Below 1 Ω
      1 (-) - 2 (TWL-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

    OK

  14. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Replace the front No. 2 speaker assembly.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.

      Tech Tips


      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both LH and RH sides.

      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  15. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. A01T9OZC30
      *a

      Component without harness connected

      (Rear Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 3.2 to 4.8 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

  16. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)


    1. Disconnect the E91 stereo component amplifier assembly connector.

    2. Disconnect the G1 and H1 front No. 1 speaker assembly connectors.

    3. Disconnect the G4 and H5 front No. 2 speaker assembly connectors.

    4. Disconnect the J2 and K2 rear speaker assembly connectors.

    5. Disconnect the L44 No. 1 speaker with box assembly connector.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E91-15 (FR+) or G1-1 - Body ground Always 10 kΩ or higher
      E91-30 (FR-) or G1-2 - Body ground Always 10 kΩ or higher
      E91-12 (FL+) or H1-1 - Body ground Always 10 kΩ or higher
      E91-27 (FL-) or H1-2 - Body ground Always 10 kΩ or higher
      E91-13 (TWR+) or G4-4 - Body ground Always 10 kΩ or higher
      E91-28 (TWR-) or G4-2 - Body ground Always 10 kΩ or higher
      E91-14 (TWL+) or H5-4 - Body ground Always 10 kΩ or higher
      E91-29 (TWL-) or H5-2 - Body ground Always 10 kΩ or higher
      E91-11 (RR+)or J2-1 (+) - Body ground Always 10 kΩ or higher
      E91-26 (RR-) or J2-2 (-) - Body ground Always 10 kΩ or higher
      E91-10 (RL+) or K2-1 (+) - Body ground Always 10 kΩ or higher
      E91-25 (RL-) or K2-2 (-) - Body ground Always 10 kΩ or higher
      E91-9 (WFR+) or L44-1 (WF+) - Body ground Always 10 kΩ or higher
      E91-24 (WFR-) or L44-3 (WF-) - Body ground Always 10 kΩ or higher
      E91-8 (WFL+) or L44-4 (WF+) - Body ground Always 10 kΩ or higher
      E91-23 (WFL-) or L44-2 (WF-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  17. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. A01T9OZC30
      *a

      Component without harness connected

      (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 3.2 to 5.2 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  18. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. A01TAH2C12
      *a

      Component without harness connected

      (Front No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      4 - 2 Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

    OK

  19. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Replace the front No. 2 speaker assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.

      Tech Tips


      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left speaker is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both the LH and RH side.

      Result
      Proceed to
      OK
      NG

    OK

    END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE)

    NG

  20. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. A01T9OZC69
      *a

      Component without harness connected

      (Rear Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (+) - 2 (-) Always 3.6 to 4.4 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

    OK

  21. REPLACE REAR SPEAKER ASSEMBLY


    1. Replace the rear speaker assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.

      Tech Tips


      • Connect all the connectors to the rear speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left speaker is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both the LH and RH side.

      Result
      Proceed to
      OK
      NG

    OK

    END (REAR SPEAKER ASSEMBLY WAS DEFECTIVE)

    NG

  22. INSPECT NO. 1 SPEAKER WITH BOX ASSEMBLY


    1. Remove the No. 1 speaker with box assembly.

      for Wagon: Click here

      for Hatchback: Click here

    2. A01TB6EC17
      *a

      Component without harness connected

      (No. 1 Speaker with Box Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (WF+) - 3 (WF-) Always 4.0 to 6.4 Ω
      2 (WF-) - 4 (WF+) Always 4.0 to 6.4 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here

    NG

    REPLACE NO. 1 SPEAKER WITH BOX ASSEMBLY for Wagon: Click here
    REPLACE NO. 1 SPEAKER WITH BOX ASSEMBLY for Hatchback: Click here