AUDIO AND VISUAL SYSTEM(for Sedan Radio and Display Type) Radio Receiver Power Source Circuit

DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

A01T9BGE07

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. CONFIRM MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      w/o Stop and Start System A
      w/ Stop and Start System B

    B

    CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ENGINE STOP AND START ECU) Click here

    A

  2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)


    1. Disconnect the E1 and E60 radio and display receiver assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E1-7 (GND1) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E1-4 (+B1) - E1-7 (GND1) Always 11 to 14 V
      E1-3 (ACC1) - E1-7 (GND1) Ignition switch ACC 11 to 14 V
      E60-1 (IG) - E1-7 (GND1) Ignition switch ON 11 to 14 V
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  3. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ENGINE STOP AND START ECU)


    1. Disconnect the E1 radio and display receiver assembly connector.

    2. Disconnect the E24 engine stop and start ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E1-4 (+B1) - E24-2 (BO1) Always Below 1 Ω
      E1-3 (ACC1) - E24-3 (ACO) Always Below 1 Ω
      E1-4 (+B1) - Body ground Always 10 kΩ or higher
      E1-3 (ACC1) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)


    1. Disconnect the E1 and E60 radio and display receiver assembly connectors.

    2. Reconnect the E24 engine stop and start ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E1-7 (GND1) - Body ground Always Below 1 Ω

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E1-4 (+B1) - E1-7 (GND1) Always 9.5 to 14 V
      E1-3 (ACC1) - E1-7 (GND1) Ignition switch ACC 9.5 to 14 V
      E60-1 (IG) - E1-7 (GND1) Ignition switch ON 11 to 14 V
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    GO TO STOP AND START SYSTEM Click here