ANTI-LOCK BRAKE SYSTEM(for Type A) DATA LIST / ACTIVE TEST

SST
A00Y6CU 09843-18040 Diagnosis Check Wire No. 2

  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the GTS on.

    6. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    7. According to the display on the GTS, read the Data List.


      Chassis > ABS/VSC/TRC > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      ABS Warning Light ABS warning light ON or OFF

      ON: Warning light on

      OFF: Warning light off

      		 -
      Brake Warning Light Brake warning light ON or OFF

      ON: Warning light on

      OFF: Warning light off

      		 -
      Stop Light SW Stop light switch ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -
      Parking Brake SW Parking brake switch ON or OFF

      ON: Parking brake applied

      OFF: Parking brake released

      		 -
      FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
      FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
      RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
      RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
      Vehicle Speed Maximum wheel speed sensor reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
      FR Wheel Acceleration Front wheel RH acceleration

      Min.: -200.84 m/s2, Max.: 199.27 m/s2

      		- During deceleration/acceleration: Changes continuously
      FL Wheel Acceleration Front wheel LH acceleration

      Min.: -200.84 m/s2, Max.: 199.27 m/s2

      		- During deceleration/acceleration: Changes continuously
      RR Wheel Acceleration Rear wheel RH acceleration

      Min.: -200.84 m/s2, Max.: 199.27 m/s2

      		- During deceleration/acceleration: Changes continuously
      RL Wheel Acceleration Rear wheel LH acceleration

      Min.: -200.84 m/s2, Max.: 199.27 m/s2

      		- During deceleration/acceleration: Changes continuously
      FR Wheel Direction Front wheel RH direction Forward or Back Forward: Forward No change
      FL Wheel Direction Front wheel LH direction Forward or Back Forward: Forward No change
      RR Wheel Direction Rear wheel RH direction Forward or Back Forward: Forward No change
      RL Wheel Direction Rear wheel LH direction Forward or Back Forward: Forward No change
      FR Wheel ABS Ctrl Status Front wheel RH ABS control status ON or OFF ON: During control -
      FL Wheel ABS Ctrl Status Front wheel LH ABS control status ON or OFF ON: During control -
      RR Wheel ABS Ctrl Status Rear wheel RH ABS control status ON or OFF ON: During control -
      RL Wheel ABS Ctrl Status Rear wheel LH ABS control status ON or OFF ON: During control -
      FR Wheel EBD Ctrl Status Front wheel RH EBD control status ON or OFF ON: During control -
      FL Wheel EBD Ctrl Status Front wheel LH EBD control status ON or OFF ON: During control -
      RR Wheel EBD Ctrl Status Rear wheel RH EBD control status ON or OFF ON: During control -
      RL Wheel EBD Ctrl Status Rear wheel LH EBD control status ON or OFF ON: During control -
      Solenoid Relay ABS solenoid relay ON or OFF

      ON: Solenoid relay on

      OFF: Solenoid relay off

      		 -
      ECB Motor Relay ABS motor relay ON or OFF

      ON: Motor relay on

      OFF: Motor relay off

      		 ECB: Electronically Controlled Brake
      ABS Solenoid (SFRH) ABS solenoid (SFRH) ON or OFF ON: During control -
      ABS Solenoid (SFRR) ABS solenoid (SFRR) ON or OFF ON: During control -
      ABS Solenoid (SFLH) ABS solenoid (SFLH) ON or OFF ON: During control -
      ABS Solenoid (SFLR) ABS solenoid (SFLR) ON or OFF ON: During control -
      ABS Solenoid (SRRH) ABS solenoid (SRRH) ON or OFF ON: During control -
      ABS Solenoid (SRRR) ABS solenoid (SRRR) ON or OFF ON: During control -
      ABS Solenoid (SRLH) ABS solenoid (SRLH) ON or OFF ON: During control -
      ABS Solenoid (SRLR) ABS solenoid (SRLR) ON or OFF ON: During control -
      BS1 Voltage Value +BS voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to battery voltage
      MT Voltage Value Motor voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to battery voltage
      Number of DTC Number of DTC recorded Min.: 0, Max.: 255 - -
      IG Voltage Value Decreased +BS voltage value decrease detection Error or Normal

      Error: Voltage low

      Normal: Normal

      		 -
      IG Voltage Value Increased +BS voltage value increase detection Error or Normal

      Error: Voltage high

      Normal: Normal

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed.

    Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the GTS on.

    6. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    7. According to the display on the GTS, perform the Active Test.


      Chassis > ABS/VSC/TRC > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      ABS Warning Light ABS warning light Warning light ON/OFF Observe combination meter assembly
      Brake Warning Light Brake warning light Warning light ON/OFF Observe combination meter assembly
      ABS Solenoid (SRLR) ABS solenoid (SRLR) Solenoid ON/OFF -
      ABS Solenoid (SRLH) ABS solenoid (SRLH) Solenoid ON/OFF -
      ABS Solenoid (SRRR) ABS solenoid (SRRR) Solenoid ON/OFF -
      ABS Solenoid (SRRH) ABS solenoid (SRRH) Solenoid ON/OFF -
      ABS Solenoid (SFLR) ABS solenoid (SFLR) Solenoid ON/OFF -
      ABS Solenoid (SFLH) ABS solenoid (SFLH) Solenoid ON/OFF -
      ABS Solenoid (SFRR) ABS solenoid (SFRR) Solenoid ON/OFF -
      ABS Solenoid (SFRH) ABS solenoid (SFRH) Solenoid ON/OFF -
      ABS Solenoid ABS solenoid (SRLR, SRLH, SRRR, SRRH, SFLR, SFLH, SFRR, SFRH)

      Solenoid SRLR/SRLH/SRRR/

      SRRH/SFLR/SFLH/SFRR/SFRH

      		 Operation sound of solenoid (clicking sound) can be heard