FRONT SUSPENSION MEMBER INSTALLATION

PROCEDURE


  1. INSTALL FRONT STABILIZER BAR

    Click here

  2. INSTALL FRONT SUSPENSION MEMBER BRACE

    Click here

  3. TEMPORARILY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH


    1. Temporarily tighten the front lower No. 1 suspension arm sub-assembly LH to the front suspension crossmember sub-assembly with the 2 bolts and nut.

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

  4. TEMPORARILY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  5. INSTALL STEERING LINK ASSEMBLY

    Click here

  6. INSTALL FRONT CROSS MEMBER SUB-ASSEMBLY


    1. Using a jack and wooden blocks, support the engine and transaxle assembly.

    2. Install the front cross member sub-assembly with the 4 bolts.

      Torque:
      99 N*m  { 1010 kgf*cm, 73 ft.*lbf }

    3. Connect the front engine mounting insulator to the front cross member sub-assembly with the 2 bolts.

      Torque:
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }

  7. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    1. Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.

      CAUTION:


      • The front suspension crossmember sub-assembly is a heavy component. Make sure that it is supported securely.

      • Make sure to secure the front suspension crossmember sub-assembly to prevent it from dropping.

      Note

      Use the attachments to keep the front suspension crossmember sub-assembly level.

    2. Uniformly tighten 2 bolts while alternately inserting SST into the left and right side reference holes in the front suspension crossmember sub-assembly.

      SST
      09670-00020
      A01TCMUC03
      *a OK *b NG
      A01TBGJ Front of the Vehicle - -
      Torque:
      137 N*m  { 1397 kgf*cm, 101 ft.*lbf }

    3. Lower the engine lifter.

    4. Connect the rear engine mounting insulator to the front suspension crossmember sub-assembly with the 2 bolts and 2 nuts.

      Torque:
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }

    5. for 1ZR-FE, 1ZR-FAE, 2ZR-FE, 8NR-FTS:


      1. Install the 2 wiring harness clamp brackets to the front suspension crossmember sub-assembly with the 2 bolts.

        Torque:
        12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }

  8. INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH


    1. A01TC82N01

      Type A:


      1. Install the front suspension member rear brace LH with the 2 bolts (B) and bolt (A).

        Torque:
        Bolt A
        137 N*m  { 1397 kgf*cm, 101 ft.*lbf }
        Bolt B
        93 N*m  { 948 kgf*cm, 69 ft.*lbf }

      2. Install the clip.

    2. A01TAITN01

      Type B:


      1. Install the front suspension member rear brace LH with the 2 bolts (B) and bolt (A).

        Torque:
        Bolt A
        137 N*m  { 1397 kgf*cm, 101 ft.*lbf }
        Bolt B
        93 N*m  { 948 kgf*cm, 69 ft.*lbf }

  9. INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH

    Tech Tips

    Perform the same procedure as for the LH side.

  10. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH


    1. A01TCLYN01

      Install the front suspension member reinforcement LH with the 4 bolts.

      Torque:
      99 N*m  { 1010 kgf*cm, 73 ft.*lbf }

      Note

      Temporarily tighten the bolt (A) and bolt (B), and then fully tighten the 4 bolts in the order of C, B, D and A.

  11. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH


    1. A01TD0RN01

      Install the front suspension member reinforcement RH with the 4 bolts.

      Torque:
      99 N*m  { 1010 kgf*cm, 73 ft.*lbf }

      Note

      Temporarily tighten the bolt (A) and bolt (B), and then fully tighten the 4 bolts in the order of C, B, D and A.

  12. INSTALL FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT (w/ Reinforcement)


    1. Install the front engine mounting bracket lower reinforcement with the 2 bolts.

      Torque:
      99 N*m  { 1010 kgf*cm, 73 ft.*lbf }

  13. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

    Click here

  14. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  15. CONNECT TIE ROD END SUB-ASSEMBLY LH

    Click here

  16. CONNECT TIE ROD END SUB-ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  17. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


    1. Install the front stabilizer link assembly LH to the front stabilizer bar with the nut.

      Torque:
      74 N*m  { 755 kgf*cm, 55 ft.*lbf }

      Note

      Do not damage the boot of the ball joint.

      Tech Tips

      If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.

  18. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  19. CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

    Click here

  20. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

    Click here

  21. INSTALL COLUMN HOLE COVER SILENCER SHEET

    Click here

  22. INSTALL FRONT WHEELS

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  23. STABILIZE SUSPENSION

    Click here

  24. FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

    Click here

  25. FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

    except 8NR-FTS: Click here

    for 8NR-FTS: Click here

  26. INSTALL REAR ENGINE UNDER COVER LH

  27. INSTALL REAR ENGINE UNDER COVER RH

  28. INSTALL FRONT NO. 3 ENGINE UNDER COVER (for Full Cover Type)

  29. INSTALL CENTER NO. 4 ENGINE UNDER COVER (w/ Cover)

  30. INSTALL NO. 1 ENGINE UNDER COVER

  31. INSTALL FRONT LOWER BUMPER ABSORBER

  32. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click here