ENTRY AND START SYSTEM(for Entry Function) Driver Side Door Entry Lock Function does not Operate

DESCRIPTION

If the entry lock function does not operate for the driver door only, but the entry unlock function operates, the request code is being transmitted properly from the driver door. In this case, there may be a problem related to the front door outside handle assembly (for driver door) (lock sensor) (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) (lock sensor)).

WIRING DIAGRAM

A01TBNKE77

CAUTION / NOTICE / HINT

Note


  • The entry and start system (for Entry Function) uses CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

  • When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • Check that there are no electrical key transmitter sub-assemblies in the vehicle.

  • Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.

    Click here

  • Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution.

    Click here

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

PROCEDURE


  1. CHECK POWER DOOR LOCK CONTROL SYSTEM


    1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

      except Sedan: Click here

      for Sedan: Click here

      OK
      Door locks operate normally.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM except Sedan: Click here
    GO TO POWER DOOR LOCK CONTROL SYSTEM for Sedan: Click here

    OK

  2. READ VALUE USING GTS (D-DOOR TRIGGER SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Entry&Start / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Entry&Start > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      D-Door Trigger Switch Driver door touch sensor (lock sensor) ON or OFF

      ON: Driver door touch sensor (lock sensor) touched

      OFF: Driver door touch sensor (lock sensor) not touched

      • Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

      • Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.

      Body Electrical > Entry&Start > Data List
      Tester Display
      D-Door Trigger Switch
      OK
      The GTS display changes correctly in response to the operation of the front door outside handle assembly (for driver door).
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

  3. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE ASSEMBLY - CERTIFICATION ECU)


    1. Disconnect the H13*1, G7*2 front door outside handle assembly (for driver door) connector.


      • *1: for LHD

      • *2: for RHD

    2. Disconnect the E35 and E33 certification ECU (smart key ECU assembly) connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      H13-1 (TRG+) - E35-20 (TSW1) Always Below 1 Ω
      E33-11 (E) - Body ground Always Below 1 Ω
      H13-1 (TRG+) or E35-20 (TSW1) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      G7-1 (TRG+) - E35-20 (TSW1) Always Below 1 Ω
      E33-11 (E) - Body ground Always Below 1 Ω
      G7-1 (TRG+) or E35-20 (TSW1) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) (DRIVER DOOR LOCK SENSOR SIGNAL INPUT)


    1. Connect the H13*1, G7*2 front door outside handle assembly (for driver door) connector.


      • *1: for LHD

      • *2: for RHD

      A01TC5HC33
      *a

      Component with harness connected

      (Certification ECU (Smart Key ECU Assembly))

      		 *b Waveform
      *c In actuality, sampling is being performed - -

    2. Connect the E35 and E33 certification ECU (smart key ECU assembly) connectors.

    3. Using an oscilloscope, check the waveform.

      OK
      Tester Connection Condition Tool Setting Specified Condition
      E35-20 (TSW1) - E33-11 (E)

      Procedure:


      1. Engine switch off

      2. Electrical key transmitter sub-assembly brought outside vehicle

      3. All doors closed

      4. Driver door lock sensor not touched → touched

      		 2 V/DIV., 500 ms/DIV.

      Pulse generation

      (See waveform)
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) for Sedan: Click here
    REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) except Sedan: Click here