CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM(for 1ZR-FAE) Shift Paddle Switch Circuit

DESCRIPTION

When the shift lever is in M, the shift range can be changed using the shift paddle switches. It is also possible to select the shift range when the vehicle is being driven with the shift lever in D by operating the shift paddle switches.

WIRING DIAGRAM

A01T8XCE02

PROCEDURE


  1. READ VALUE USING GTS (SPORTS SHIFT UP SWITCH AND SPORTS SHIFT DOWN SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List.

    5. According to the display on the GTS, read the Data List.


      Powertrain > Engine and ECT > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Sports Shift Up SW Sport shift up switch status OFF or ON

      • ON: Shift lever held in "+" or "+" shift paddle switch pulled

      • OFF: Shift lever not held in "+" and "+" shift paddle switch released

      		 -
      Sports Shift Down SW Sport shift down switch status OFF or ON

      • ON: Shift lever held in "-" or "-" shift paddle switch pulled

      • OFF: Shift lever not held in "-" and "-" shift paddle switch released

      		 -

      Powertrain > Engine and ECT > Data List
      Tester Display
      Sports Shift Up SW
      Sports Shift Down SW
      Result
      Result Proceed to
      Data List value is normal A
      Data List value is not normal B

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

    B

  2. INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY (SHIFT PADDLE SWITCH)


    1. Disconnect the A50 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A50-42 (SFTU) - Body ground "+" (Up shift) shift paddle operated and held Below 3 Ω
      A50-42 (SFTU) - Body ground "+" (Up shift) shift paddle not operated 10 kΩ or higher
      A50-43 (SFTD) - Body ground "-" (Down shift) shift paddle operated and held Below 3 Ω
      A50-43 (SFTD) - Body ground "-" (Down shift) shift paddle not operated 10 kΩ or higher

    3. Connect the A50 ECM connector.

      Result
      Proceed to
      OK
      NG

    OK

    GO TO TRANSMISSION CONTROL SWITCH CIRCUIT Click here

    NG

  3. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)


    1. Disconnect the E6 spiral cable sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E6-2 (ECC) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

    OK

  4. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)


    1. Disconnect the A50 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A50-43 (SFTD) - E6-7 (SDN) Always Below 1 Ω
      A50-43 (SFTD) or E6-7 (SDN) - Body ground and other terminals Always 10 kΩ or higher
      A50-42 (SFTU) - E6-14 (SUP) Always Below 1 Ω
      A50-42 (SFTU) or E6-14 (SUP) - Body ground and other terminals Always 10 kΩ or higher

    3. Connect the A50 ECM connector.

    4. Connect the E6 spiral cable sub-assembly connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)

    OK

  5. CHECK WIRE HARNESS AND CONNECTORS (STEERING PAD SWITCH ASSEMBLY)


    1. A01TD14C07
      *a

      Front view of wire harness connector

      (to Spiral Cable Sub-assembly)

      Disconnect the z1 steering pad switch assembly connector from the spiral cable sub-assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z1-6 (SUP) - z1-7 (ECC) "+" (Up shift) shift paddle operated and held Below 3 Ω
      z1-6 (SUP) - z1-7 (ECC) "+" (Up shift) shift paddle not operated 10 kΩ or higher
      z1-12 (SDN) - z1-7 (ECC) "-" (Down shift) shift paddle operated and held Below 3 Ω
      z1-12 (SDN) - z1-7 (ECC) "-" (Down shift) shift paddle not operated 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY (SHIFT PADDLE SWITCH) Click here

    OK

  6. INSPECT SPIRAL CABLE SUB-ASSEMBLY


    1. Disconnect the z1 and E6 spiral cable sub-assembly connectors.

      A01TCEBC01
      *a

      Component without harness connected

      (Spiral Cable Sub-assembly)

      		 *b Steering Pad Switch Side
      *c Vehicle Side - -

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z1-7 (ECC) - E6-2 (ECC) Always Below 3 Ω
      z1-6 (SUP) - E6-14 (SUP) Always Below 3 Ω
      z1-12 (SDN) - E6-7 (SDN) Always Below 3 Ω
      z1-7 (ECC) or E6-2 (ECC) - Body ground and other terminals Always 10 kΩ or higher
      z1-6 (SUP) or E6-14 (SUP) - Body ground and other terminals Always 10 kΩ or higher
      z1-12 (SDN) or E6-7 (SDN) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SPIRAL CABLE SUB-ASSEMBLY w/o VSC: Click here
    REPLACE SPIRAL CABLE SUB-ASSEMBLY w/ VSC: Click here

    OK

  7. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM INITIALIZATION Click here

  8. INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY (SHIFT PADDLE SWITCH)


    1. A01TCQ9C09
      *a

      Component without harness connected

      (Shift Paddle Switch LH)
      *b

      Component without harness connected

      (Shift Paddle Switch RH)

      Disconnect the C and B transmission shift switch assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Shift Paddle Switch LH:
      Tester Connection Condition Specified Condition
      C-3 (ECC) - C-2 (SFTD) "-" (Down shift) shift paddle operated and held Below 3 Ω
      C-3 (ECC) - C-2 (SFTD) "-" (Down shift) shift paddle not operated 10 kΩ or higher
      C-4 (ECC1) - C-2 (SFTD) "-" (Down shift) shift paddle operated and held Below 3 Ω
      C-4 (ECC1) - C-2 (SFTD) "-" (Down shift) shift paddle not operated 10 kΩ or higher
      Shift Paddle Switch RH:
      Tester Connection Condition Specified Condition
      B-3 (SFTU) - B-2 (ECC1) "+" (Up shift) shift paddle operated and held Below 3 Ω
      B-3 (SFTU) - B-2 (ECC1) "+" (Up shift) shift paddle not operated 10 kΩ or higher

    3. Connect the C and B transmission shift switch assembly connectors.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE TRANSMISSION SHIFT SWITCH ASSEMBLY (SHIFT PADDLE SWITCH) Click here

    OK

  9. INSPECT NO. 1 SWITCH WIRE


    1. A01TCWIC03
      *a

      Front view of wire harness connector

      (to Steering Pad Switch Assembly)

      Disconnect the A No. 1 switch wire connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-2 (SFTU) - A-7 (ECC) "+" (Up shift) shift paddle operated and held Below 3 Ω
      A-2 (SFTU) - A-7 (ECC) "+" (Up shift) shift paddle not operated 10 kΩ or higher
      A-3 (SFTD) - A-7 (ECC) "-" (Down shift) shift paddle operated and held Below 3 Ω
      A-3 (SFTD) - A-7 (ECC) "-" (Down shift) shift paddle not operated 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE STEERING PAD SWITCH ASSEMBLY Click here

    NG

    REPLACE NO. 1 SWITCH WIRE Click here