CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM(for 8NR-FTS), Diagnostic DTC:P084015

DTC Code DTC Name
P084015 Transmission Fluid Pressure Sensor/Switch "A" Circuit Short To Battery or Open

DESCRIPTION

The ECM performs learning control for the belt clamping pressure based on the belt clamping pressure signal, which is output by the oil pressure sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P084015 Transmission Fluid Pressure Sensor/Switch "A" Circuit Short To Battery or Open

1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other


  1. 2 seconds or more after engine start

  2. Open or short to B+ in oil pressure sensor circuit

  3. 0.5 seconds

  4. 1-trip detection logic

  • Wire harness or connector

  • Oil pressure sensor

  • ECM

 Comes on DTC stored

SAE Code:

P0843

MONITOR DESCRIPTION

This DTC indicates an open in the oil pressure sensor circuit. If there is an open or short in the oil pressure sensor circuit, the ECM detects the malfunction, illuminates the MIL and stores a DTC.

WIRING DIAGRAM

Refer to DTC P084011.

Click here

CAUTION / NOTICE / HINT

Tech Tips

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Start the engine and wait for 2 seconds or more.

  2. Check for DTCs again.

    Click here

PROCEDURE


  1. READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)

    CAUTION:

    A stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.

    Note


    • This test must be performed after checking and confirming that the engine is normal.

    • Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).

    • Perform this test with the air conditioning off.

    • Do not perform the stall speed test for longer than 5 seconds.

    • When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.


    1. Warm up the engine.

    2. Fully apply the parking brake and chock all 4 wheels.

    3. Connect the GTS to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Transmission / Active Test / Activate the TC Terminal.


      Powertrain > Transmission > Active Test
      Active Test Display
      Activate the TC Terminal
      Data List Display
      Belt Clamping Force Sensor

    7. According to the display on the GTS, perform the Active Test.

    8. According to the display on the GTS, read the Data List.


      Powertrain > Transmission > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Belt Clamping Force Sensor Secondary oil pressure value

      Min.: -64 MPa

      Max.: 63.998 MPa

      Secondary oil pressure inspection:


      • 3.5 to 5.5 MPa (35.6 to 56.1 kgf/cm2, 507 to 798 psi): D position stall test

      • 3.6 to 5.5 MPa (36.7 to 56.1 kgf/cm2, 522 to 798 psi): R position stall test

      		 -
      Result
      Result Proceed to
      Data List value is not normal A
      Data List value is normal B

    B

    REPLACE ECM Click here

    A

  2. CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - ECM)


    1. Disconnect the B30 oil pressure sensor connector.

    2. Disconnect the B208 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B30-1 (E2) - B208-117 (EPTO) Always Below 1 Ω
      B30-2 (PTO) - B208-86 (PTO) Always Below 1 Ω
      B30-3 (VC) - B208-118 (VCPT) Always Below 1 Ω
      B30-1 (E2) or B208-117 (EPTO) - Other terminals Always 10 kΩ or higher
      B30-2 (PTO) or B208-86 (PTO) - Other terminals Always 10 kΩ or higher
      B30-3 (VC) or B208-118 (VCPT) - Other terminals Always 10 kΩ or higher

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      B208-86 (PTO) - Body ground Ignition switch ON Below 1 V
      B30-2 (PTO) - Body ground Ignition switch ON Below 1 V

    5. Connect the B208 ECM connector.

    6. Connect the B30 oil pressure sensor connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (OIL PRESSURE SENSOR - ECM)

    OK

  3. CHECK ECM (VCPT TERMINAL VOLTAGE)


    1. B0043JJC16
      *a

      Front view of wire harness connector

      (to Oil Pressure Sensor)

      Disconnect the B30 oil pressure sensor connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      B30-3 (VC) - B30-1 (E2) Ignition switch ON 4.75 to 5.25 V

    3. Connect the B30 oil pressure sensor connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE ECM Click here

    OK

  4. REPLACE OIL PRESSURE SENSOR


    1. Replace the oil pressure sensor.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM INITIALIZATION Click here

  5. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM INITIALIZATION Click here

  6. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM INITIALIZATION Click here