CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM, Diagnostic DTC:P2716

DTC Code DTC Name
P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

DESCRIPTION

The ECM uses signals to control shift solenoid valve SLT to provide optimum line pressure control. Shift solenoid valve SLT is also used during forward and reverse clutch engagement to control the oil pressure to the forward and reverse clutch.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

  1. Diagnosis Condition


    • The vehicle is being driven.

  2. Malfunction Status


    • There is an open or short circuit in the shift solenoid valve SLT circuit.

  3. Malfunction Time


    • 1 second or more

  4. Other


    • 1-trip detection logic

  • Wire harness or connector

  • Continuously variable transaxle assembly (Shift solenoid valve SLT)

  • ECM

 Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates an open or short circuit in the shift solenoid valve SLT circuit. When there is an open or short circuit in the shift solenoid valve SLT circuit, the ECM detects the problem, illuminates the MIL and stores this DTC.

WIRING DIAGRAM

A01T8V9E29
*a Shift Solenoid Valve SLT
*b Continuously Variable Transaxle Assembly (Transmission Wire)

PROCEDURE


  1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)


    1. A01T9G9C32
      *a

      Component without harness connected

      (Transmission Wire)

      Disconnect the B90 transmission wire connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SLT+) - 7 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
      2 (SLT+) - Body ground and other terminals Always 10 kΩ or higher
      7 (SLT-) - Body ground and other terminals Always 10 kΩ or higher

    3. Connect the B90 transmission wire connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    1. Disconnect the B31 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B31-67 (SLT+) - B31-66 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
      B31-67 (SLT+) - Body ground and other terminals Always 10 kΩ or higher
      B31-66 (SLT-) - Body ground and other terminals Always 10 kΩ or higher

    3. Connect the B31 ECM connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

    OK

  3. REPLACE ECM


    1. Replace the ECM.


      Result
      Proceed to
      NEXT

    NEXT

  4. PERFORM INITIALIZATION

    Note


    • Performing Reset Memory will clear the learned value of the yaw rate and acceleration sensor (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform Reset Memory, yaw rate and acceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:

      Replaced Part

      • Continuously variable transaxle assembly

      • ECM

      • Oil pressure sensor

      • Airbag sensor assembly (Yaw rate and acceleration sensor)

    • After performing Reset Memory, always perform yaw rate and acceleration sensor (deceleration sensor zero point) calibration first, and then CVT oil pressure calibration.

    • Always perform calibration with the vehicle on level ground.

    • Do not shake or vibrate the vehicle during calibration.


    1. Using the GTS, perform Reset Memory, deceleration sensor zero point calibration and CVT oil pressure calibration.

      Click here

    2. Check for DTCs again.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    END

  5. REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY


    1. Replace the continuously variable transaxle assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  6. PERFORM INITIALIZATION

    Note


    • Performing Reset Memory will clear the learned value of the yaw rate and acceleration sensor (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform Reset Memory, yaw rate and acceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:

      Replaced Part

      • Continuously variable transaxle assembly

      • ECM

      • Oil pressure sensor

      • Airbag sensor assembly (Yaw rate and acceleration sensor)

    • After performing Reset Memory, always perform yaw rate and acceleration sensor (deceleration sensor zero point) calibration first, and then CVT oil pressure calibration.

    • Always perform calibration with the vehicle on level ground.

    • Do not shake or vibrate the vehicle during calibration.


    1. Using the GTS, perform Reset Memory, deceleration sensor zero point calibration and CVT oil pressure calibration.

      Click here

    2. Check for DTCs again.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    END