MULTI-MODE MANUAL TRANSAXLE UNIT COMPONENTS
ILLUSTRATION
| *1 | SHIFT AND SELECT ACTUATOR ASSEMBLY | *2 | BREATHER PROTECTOR |
| *3 | CLUTCH RELEASE BLEEDER SUB-ASSEMBLY | *4 | RELEASE CYLINDER BLEEDER PLUG |
| *5 | RELEASE CYLINDER BLEEDER PLUG CAP | *6 | CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY |
| *7 | CLUTCH RELEASE CYLINDER TO BLEEDER TUBE | *8 | TRANSMISSION REVOLUTION SENSOR |
| *9 | BACK-UP LIGHT SWITCH ASSEMBLY | *10 | MANUAL TRANSMISSION DRAIN PLUG |
| *11 | MANUAL TRANSMISSION FILLER PLUG | *12 | NEUTRAL POSITION SWITCH |
| *13 | NO. 1 CLUTCH HOUSING COVER | *14 | CLUTCH TUBE BOOT |
| *15 | RING PIN | *16 | BREATHER PLUG |
| *17 | O-RING | *18 | GASKET |
| *19 | BREATHER PLUG CAP | *20 | WIRE HARNESS BRACKET |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Clutch spline grease | - | - |
ILLUSTRATION
| *1 | SHIFT DETENT BALL PLUG | *2 | SHIFT DETENT BALL COMPRESSION SPRING |
| *3 | SHIFT DETENT BALL | *4 | TRANSMISSION CASE PLUG |
| *5 | TRANSMISSION CASE GASKET | *6 | REVERSE IDLER GEAR SHAFT BOLT |
| *7 | STRAIGHT PIN | *8 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *1 | SHIFT AND SELECT LEVER SHAFT ASSEMBLY | *2 | SHIFT INTER LOCK PLATE |
| *3 | DIFFERENTIAL CASE ASSEMBLY | *4 | FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
| *5 | FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING | *6 | REVERSE SHIFT ARM BRACKET ASSEMBLY |
| *7 | REVERSE SHIFT FORK SHAFT ASSEMBLY | *8 | REVERSE IDLER GEAR SUB-ASSEMBLY |
| *9 | REVERSE IDLER THRUST WASHER | *10 | REVERSE IDLER GEAR SHAFT |
| *11 | NO. 1 GEAR SHIFT FORK SHAFT ASSEMBLY | *12 | OUTPUT SHAFT ASSEMBLY |
| *13 | NO. 2 GEAR SHIFT FORK SHAFT ASSEMBLY | *14 | NO. 3 GEAR SHIFT FORK SHAFT ASSEMBLY |
| *15 | INPUT SHAFT ASSEMBLY | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | SHIFT AND SELECT LEVER SHAFT | *2 | INNER NO. 1 SHIFT LEVER |
| *3 | SHIFT AND SELECT LEVER SHAFT HEAD | *4 | INNER SELECT LEVER |
| *5 | FRONT INNER SHIFT LEVER | *6 | INNER NO. 2 SHIFT LEVER |
| *7 | SLOTTED SPRING PIN | - | - |
ILLUSTRATION
| *1 | TRANSMISSION OIL SEPARATOR | *2 | TRANSAXLE CASE OIL SEAL (for RH SIDE) |
| *3 | FRONT TRANSAXLE CASE OIL SEAL | *4 | TRANSMISSION MAGNET |
| *5 | FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE) | *6 | FRONT DIFFERENTIAL CASE FRONT PLATE WASHER |
| *7 | OUTPUT SHAFT COVER | *8 | FRONT OUTPUT SHAFT BEARING (OUTER RACE) |
| *9 | FRONT TRANSAXLE CASE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | - | - |
ILLUSTRATION
| *1 | MANUAL TRANSMISSION CASE | *2 | TRANSMISSION OIL SEPARATOR |
| *3 | NO. 1 OIL RECEIVER PIPE | *4 | FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE) |
| *5 | FRONT DIFFERENTIAL CASE REAR PLATE WASHER | *6 | REAR INPUT SHAFT BEARING SHIM |
| *7 | INPUT SHAFT COVER | *8 | REAR OUTPUT SHAFT BEARING (OUTER RACE) |
| *9 | REAR OUTPUT SHAFT BEARING SHIM | *10 | TRANSMISSION CASE OIL SEAL (for LH SIDE) |
| *11 | MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | - | - |