MANUAL TRANSAXLE UNIT COMPONENTS
ILLUSTRATION
| *A | w/ Stop and Start System | *B | w/o Stop and Start System |
| *1 | CONTROL CABLE BRACKET ASSEMBLY | *2 | MANUAL TRANSMISSION DRAIN PLUG |
| *3 | MANUAL TRANSMISSION FILLER PLUG | *4 | NEUTRAL POSITION SWITCH |
| *5 | NO. 1 CLUTCH HOUSING COVER | *6 | RELEASE CYLINDER BLEEDER PLUG |
| *7 | RELEASE CYLINDER BLEEDER PLUG CAP | *8 | TRANSMISSION CASE PLUG |
| *9 | WIRE HARNESS CLAMP BRACKET | *10 | CLUTCH RELEASE CYLINDER TO BLEEDER TUBE |
| *11 | CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY | *12 | BACK-UP LIGHT SWITCH ASSEMBLY |
| *13 | CLUTCH RELEASE BLEEDER SUB-ASSEMBLY | *14 | BREATHER PLUG |
| *15 | CLUTCH TUBE BOOT | *16 | GASKET |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Clutch spline grease | - | - |
ILLUSTRATION
| *1 | STRAIGHT PIN | *2 | PLUG |
| *3 | SHIFT AND SELECT LEVER SHAFT COMPRESSION SPRING | *4 | LOCK BALL PIN |
| *5 | TRANSMISSION CASE PLUG | *6 | REVERSE IDLER GEAR SHAFT BOLT |
| *7 | SHIFT DETENT BALL | *8 | SHIFT DETENT BALL COMPRESSION SPRING |
| *9 | SHIFT DETENT BALL PLUG | *10 | NO. 1 LOCK BALL ASSEMBLY |
| *11 | OUTER SHIFT LEVER E-RING | *12 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Adhesive 1344 |  |
Adhesive 1324 |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *1 | OUTER SELECT LEVER | *2 | OUTER SELECT LEVER OIL SEAL |
| *3 | INNER SELECT LEVER | *4 | INNER SELECT LEVER SET BOLT |
| *5 | REVERSE SHIFT ARM BRACKET ASSEMBLY | *6 | REVERSE SHIFT FORK SHAFT ASSEMBLY |
| *7 | REVERSE IDLER GEAR SUB-ASSEMBLY | *8 | REVERSE IDLER THRUST WASHER |
| *9 | REVERSE IDLER GEAR SHAFT | *10 | INPUT SHAFT ASSEMBLY |
| *11 | NO. 3 GEAR SHIFT FORK SHAFT ASSEMBLY | *12 | NO. 2 GEAR SHIFT FORK SHAFT ASSEMBLY |
| *13 | NO. 1 GEAR SHIFT FORK SHAFT ASSEMBLY | *14 | OUTPUT SHAFT ASSEMBLY |
| *15 | FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (INNER RACE) | *16 | FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE) |
| *17 | SHIFT AND SELECT LEVER SHAFT ASSEMBLY | *18 | SHIFT INTER LOCK PLATE |
| *19 | DIFFERENTIAL CASE ASSEMBLY | *20 | SLOTTED SPRING PIN |
| *21 | REVERSE SHIFT FORK | *22 | NO. 4 GEAR SHIFT FORK SHAFT |
| *23 | NO. 1 GEAR SHIFT HEAD | *24 | NO. 1 GEAR SHIFT FORK ASSEMBLY |
| *25 | NO. 3 GEAR SHIFT HEAD | *26 | NO. 3 REVERSE PRE-BALK HEAD |
| *27 | NO. 3 GEAR SHIFT FORK ASSEMBLY | *28 | NO. 2 GEAR SHIFT HEAD |
| *29 | SNAP RING | *30 | SPACER |
| *31 | NO. 2 REVERSE PRE-BALK HEAD | *32 | STRAIGHT PIN |
| *33 | BIMETAL FORMED BUSHING | *34 | TORSION SPRING |
| *35 | SHIFT LEVER STOPPER | *36 | NO. 2 GEAR SHIFT FORK ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | |
Adhesive 1324 |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *1 | TRANSAXLE CASE OIL SEAL | *2 | FRONT OUTPUT SHAFT BEARING (OUTER RACE) |
| *3 | FRONT TRANSAXLE CASE OIL SEAL | *4 | REVERSE RESTRICT PIN ASSEMBLY |
| *5 | TRANSMISSION MAGNET | *6 | TRANSMISSION OIL SEPARATOR |
| *7 | OUTPUT SHAFT COVER | *8 | FRONT DIFFERENTIAL CASE FRONT PLATE WASHER |
| *9 | FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE) | *10 | FRONT TRANSAXLE CASE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | - | - |
ILLUSTRATION
| *1 | TRANSMISSION CASE OIL SEAL | *2 | INPUT SHAFT COVER |
| *3 | MANUAL TRANSMISSION CASE | *4 | MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY |
| *5 | NO. 1 OIL RECEIVER PIPE | *6 | OUTER NO. 1 SHIFT LEVER |
| *7 | OUTER SHIFT LEVER OIL SEAL | *8 | REAR INPUT SHAFT BEARING SHIM |
| *9 | REAR OUTPUT SHAFT BEARING (OUTER RACE) | *10 | TRANSMISSION OIL SEPARATOR |
| *11 | FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE) | *12 | REAR OUTPUT SHAFT BEARING SHIM |
| *13 | FRONT DIFFERENTIAL CASE REAR PLATE WASHER | *14 | OUTER SHIFT LEVER SPACER |
| *15 | INNER NO. 1 SHIFT LEVER | *16 | INNER SHIFT LEVER SLOTTED SPRING PIN |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | - | - |