MANUAL TRANSAXLE ASSEMBLY REMOVAL

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE NO. 1 ENGINE UNDER COVER

    Click here

  4. REMOVE STARTER ASSEMBLY

    Click here

  5. REMOVE FRONT EXHAUST PIPE ASSEMBLY

    Click here

  6. REMOVE FRONT LOWER BUMPER ABSORBER

    Click here

  7. REMOVE REAR ENGINE UNDER COVER RH

    Click here

  8. REMOVE REAR ENGINE UNDER COVER LH

    Click here

  9. DRAIN MANUAL TRANSAXLE OIL

    Click here

  10. REMOVE DRIVE SHAFT ASSEMBLY

    Click here

  11. DRAIN ENGINE COOLANT

    Click here

  12. REMOVE NO. 1 ENGINE COVER

    Click here

  13. REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE ASSEMBLY

    Click here

  14. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  15. REMOVE AIR CLEANER BRACKET


    1. A01T9UZ

      Disengage the 3 clamps to separate the wire harness.

    2. A01T9PR

      Remove the 5 bolts and air cleaner bracket.

  16. DISCONNECT ENGINE WIRE

    Click here

  17. REMOVE NO. 4 WATER BY-PASS HOSE

    Click here

  18. DISCONNECT COMPRESSOR OUTLET ELBOW

    Click here

  19. DISCONNECT NO. 2 AIR HOSE

    Click here

  20. REMOVE NO. 1 AIR TUBE ASSEMBLY


    1. A01T8XK

      Slide the clamp and disconnect the water by-pass hose assembly from the No. 2 radiator pipe.

    2. Slide the clamp and disconnect the radiator hose sub-assembly from the No. 1 radiator pipe.

    3. Disengage the clamp to disconnect the water hose sub-assembly from the compressor outlet elbow.

    4. Slide the clamp and disconnect the water hose sub-assembly from the No. 1 radiator pipe.

    5. Slide the clamp and disconnect the outlet heater water hose from the No. 2 radiator pipe.

    6. Remove the 2 bolts and No. 1 air tube assembly from the manual transaxle assembly.

  21. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    1. A01TAPF

      Remove the 2 clips and disconnect the transmission control cable assembly from the manual transaxle assembly.

    2. A01TD85

      Remove the 2 clips and disconnect the transmission control cable assembly from the control cable bracket.

    3. A01TAX0

      Remove the bolt to disconnect the bracket of the transmission control cable assembly from the rear engine mounting insulator.

  22. REMOVE NO. 1 CLUTCH HOUSING COVER


    1. A01TBLI

      Remove the 2 bolts and No. 1 clutch housing cover.

  23. REMOVE NO. 2 MANIFOLD STAY


    1. A01TA3A

      Using an E14 "TORX" socket wrench, remove the 2 bolts from the manual transaxle assembly.

    2. Remove the nut and No. 2 manifold stay.

  24. DISCONNECT CLUTCH RELEASE CYLINDER ASSEMBLY


    1. A01T92D

      Remove the 4 bolts to disconnect the clutch release cylinder assembly and clutch flexible hose bracket from the manual transaxle assembly.

  25. DISCONNECT WIRE HARNESS


    1. A01TCV2

      Remove the bolt to disconnect the ground cable.

    2. A01TDKAC01
      *a Back-up Light Switch Assembly Connector
      *b Neutral Position Switch Connector

      Disconnect the back-up light switch assembly connector.

    3. Disconnect the neutral position switch connector.

    4. Remove the 2 bolts to disconnect the wire harness.

  26. LOOSEN ENGINE AND TRANSAXLE CONNECTING BOLT


    1. Manual transaxle assembly upper side:


      1. A01T8DF

        Using an E14 "TORX" socket wrench, loosen the 2 bolts.

    2. Manual transaxle assembly lower side:


      1. A01TDO6

        Loosen the 4 bolts.

    3. Engine mounting insulator LH side:


      1. A01TAUS

        Loosen the bolt.

  27. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

    Click here

  28. SUPPORT MANUAL TRANSAXLE ASSEMBLY


    1. Support the manual transaxle assembly with a transmission jack.

      Note

      Secure the manual transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.

  29. REMOVE FRONT CROSS MEMBER SUB-ASSEMBLY


    1. A01TBUN

      Remove the 6 bolts and front cross member sub-assembly.

  30. REMOVE FRONT ENGINE MOUNTING INSULATOR


    1. A01TDS3

      Remove the through bolt, nut and front engine mounting insulator.

  31. REMOVE MANUAL TRANSAXLE ASSEMBLY


    • As there is very little space around the manual transaxle assembly, make sure that the manual transaxle assembly does not contact the vehicle body, clutch lines and radiator cooling fan when removing the manual transaxle assembly.

    • When removing the manual transaxle assembly, it is necessary to move the engine assembly and manual transaxle assembly up and down, and back and forth. Therefore, continually confirm that the parts are properly supported and stable while performing this procedure.


    1. A01TCTS

      Remove the nut and through bolt to disconnect the engine mounting insulator LH from the engine mount bracket LH.

    2. Slowly lower the transmission jack to slightly tilt the engine assembly and manual transaxle assembly.

      Tech Tips

      Lower the engine assembly and manual transaxle assembly to a position where the engine mounting insulator LH can be removed.

    3. A01T8XW

      Remove the 4 bolts and engine mounting insulator LH from the vehicle body.

    4. A01TA2F

      Remove the 4 bolts and engine mounting bracket LH from the manual transaxle assembly.

      Note

      Make sure to clean the bolts and bolt holes after removing the manual transaxle assembly.

    5. A01T9QB

      Use a cloth, etc. to protect the clutch lines as shown in the illustration.

    6. A01TC1CC01
      *a Vehicle Body
      *b Crankshaft Damper Sub-assembly

      Slowly lower the transmission jack to slightly tilt the engine assembly and manual transaxle assembly.

      Note

      Make sure that the crankshaft damper sub-assembly does not contact the vehicle body.

    7. A01T8CLC01
      *a Engine Support Point

      Support the engine assembly with an engine lifter as shown in the illustration.

    8. Using an E14 "TORX" socket wrench, remove the 2 bolts.

    9. A01T8W7C02
      *a "TORX" Bolt

      Remove the 4 bolts.

    10. While making sure that the manual transaxle assembly does not contact the clutch lines, slowly separate the manual transaxle assembly from the engine assembly until the input shaft is clear of the diaphragm spring of the clutch cover.

      Note

      To prevent damage to the dowel pins, do not pry between the manual transaxle assembly and engine assembly.

    11. Slowly lower the transmission jack to remove the manual transaxle assembly.

  32. REMOVE REAR ENGINE MOUNTING INSULATOR

    Click here

  33. REMOVE FRONT ENGINE MOUNTING BRACKET


    1. A01T8D5

      Remove the 4 bolts and front engine mounting bracket.

  34. REMOVE REAR ENGINE MOUNTING BRACKET


    1. A01T93U

      Remove the 5 bolts and rear engine mounting bracket.