MANUAL TRANSAXLE UNIT COMPONENTS
ILLUSTRATION
| *1 | SHIFT AND SELECT LEVER ASSEMBLY | *2 | SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING |
| *3 | DRAIN PLUG | *4 | GASKET |
| *5 | TRANSAXLE CASE OIL SEAL | *6 | SHIFT GATE PIN |
| *7 | NO. 1 LOCK BALL ASSEMBLY | *8 | NO. 2 LOCK BALL ASSEMBLY |
| *9 | BACK-UP LIGHT SWITCH ASSEMBLY | *10 | TRANSMISSION CASE OIL SEAL |
| *11 | SELECTING BELL CRANK ASSEMBLY | *12 | SHIFT AND SELECT PIN |
| *13 | SPRING | *14 | O-RING |
| *15 | PARK/NEUTRAL POSITION SWITCH ASSEMBLY | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
MP grease | ★ | Precoated part |
ILLUSTRATION
| *A | w/ Precoated Part | *B | w/o Precoated Part |
| *1 | CLUTCH RELEASE BEARING ASSEMBLY | *2 | CLUTCH RELEASE BEARING CLIP |
| *3 | CLUTCH RELEASE FORK SUB-ASSEMBLY | *4 | SHIFT DETENT BALL |
| *5 | RELEASE FORK SUPPORT | *6 | CLUTCH RELEASE FORK BOOT |
| *7 | SPRING | *8 | SPRING SEAT |
| *9 | DETENT BALL PLUG | *10 | REVERSE IDLER GEAR SHAFT BOLT |
| *11 | MANUAL TRANSMISSION CASE PLUG | *12 | GASKET |
| *13 | CONTROL CABLE BRACKET | *14 | MANUAL TRANSMISSION FILLER PLUG |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Release hub grease | ★ | Precoated part |
ILLUSTRATION
| *1 | OUTPUT SHAFT COVER | *2 | FRONT TRANSAXLE CASE OIL SEAL |
| *3 | INPUT SHAFT FRONT BEARING | *4 | TRANSMISSION OIL SEPARATOR |
| *5 | INPUT SHAFT ASSEMBLY | *6 | NO. 2 OUTPUT SHAFT FRONT BEARING OUTER RACE |
| *7 | NO. 2 OUTPUT SHAFT ASSEMBLY | *8 | NO. 2 OUTPUT SHAFT REAR BEARING OUTER RACE |
| *9 | OUTPUT SHAFT REAR BEARING SHIM | *10 | FRONT DIFFERENTIAL CASE FRONT BEARING OUTER RACE |
| *11 | FRONT DIFFERENTIAL CASE REAR BEARING OUTER RACE | *12 | FRONT DIFFERENTIAL CASE REAR SHIM |
| *13 | DIFFERENTIAL GEAR ASSEMBLY | *14 | TRANSMISSION MAGNET |
| *15 | OUTPUT SHAFT FRONT BEARING | *16 | NO. 1 OUTPUT SHAFT ASSEMBLY |
| *17 | OUTPUT SHAFT REAR BEARING SHAFT SNAP RING | *18 | INPUT SHAFT REAR BEARING SHAFT SNAP RING |
| *19 | NO. 1 OIL RECEIVER PIPE | *20 | MANUAL TRANSMISSION CASE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | - | - |
ILLUSTRATION
| *1 | 1ST AND 2ND SHIFT FORK SHAFT | *2 | SHIFT FORK SHAFT BEARING |
| *3 | SHIFT ARM | *4 | PIN |
| *5 | E-RING | *6 | TRANSMISSION OIL SEPARATOR |
| *7 | NEEDLE ROLLER BEARING | *8 | 5TH AND 6TH SHIFT FORK SHAFT |
| *9 | REVERSE SHIFT FORK | *10 | REVERSE SHIFT FORK SHAFT |
| *11 | NO. 1 GEAR SHIFT FORK | *12 | NO. 2 GEAR SHIFT HEAD |
| *13 | 3RD AND 4TH SHIFT FORK SHAFT | *14 | NO. 2 GEAR SHIFT FORK |
| *15 | NO. 3 GEAR SHIFT HEAD | *16 | NO. 5 GEAR SHIFT FORK SHAFT |
| *17 | REVERSE IDLER GEAR | *18 | REVERSE IDLER THRUST WASHER |
| *19 | REVERSE IDLER GEAR SHAFT | *20 | NO. 3 GEAR SHIFT FORK |
| *21 | SLOTTED SPRING PIN | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | ★ | Precoated part |