CLUTCH PEDAL(for RHD) INSTALLATION

PROCEDURE


  1. INSTALL NO. 1 CLUTCH PEDAL CUSHION


    1. Using needle-nose pliers, install the 2 No. 1 clutch pedal cushions to the clutch pedal sub-assembly.

  2. INSTALL CLUTCH PEDAL BUSHING


    1. Mount the clutch pedal sub-assembly in a soft jaw vise.

      Note

      Be careful not to damage the clutch pedal sub-assembly in the vise.

    2. A01TB2JC01
      A01TCE3 MP grease

      Apply MP grease to the inner, outer and end surfaces of 2 new clutch pedal bushings.

    3. Install the clutch pedal shaft collar and 2 clutch pedal bushings to the clutch pedal sub-assembly.

  3. INSTALL CLUTCH PEDAL PAD


    1. Install the clutch pedal pad to the clutch pedal sub-assembly.

  4. INSTALL CLUTCH PEDAL SUB-ASSEMBLY


    1. Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt and nut.

      Torque:
      36.8 N*m  { 375 kgf*cm, 27 ft.*lbf }

      Tech Tips


      • Install the bolt from the right side of the vehicle.

      • When tightening the nut, keep the bolt from rotating.

  5. INSTALL CLUTCH PEDAL SPRING (for 1NR-FE)


    1. A01TB88C01
      A01TCE3 MP grease

      Apply MP grease to the sliding portions of the clutch pedal spring.

    2. Install the clutch pedal spring to the clutch pedal sub-assembly and clutch pedal support sub-assembly.

  6. INSTALL PEDAL WITH HOOK SPRING (except 1NR-FE)


    1. A01TBM4C01
      A01TCE3 MP grease

      Apply MP grease to the sliding portions of the pedal with hook spring.

    2. Install the clutch pedal spring holder to the clutch pedal support sub-assembly.

    3. Install the pedal with hook spring to the clutch pedal sub-assembly and clutch pedal support sub-assembly.

    4. Install the over center spring cap to the clutch pedal sub-assembly.

  7. INSTALL CLUTCH PEDAL STOPPER BOLT


    1. Install the clutch pedal stopper bolt so that its end touches the No. 1 clutch pedal cushion.

      Tech Tips

      Tighten the lock nut to the specified torque when adjusting the clutch pedal.

  8. INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY


    1. A01TBUCC01
      *A for 1ZR-FAE, 1ND-TV, 1NR-FE, 8NR-FTS
      *B for 1WW
      A01TCE3 MP grease

      Apply MP grease to the sliding portion of the clutch master cylinder push rod clevis and clutch pedal sub-assembly.

    2. Install the clutch master cylinder push rod clevis to the cutout of the clutch pedal sub-assembly from the left side of the vehicle and push it downward.

    3. Install the clutch pedal support sub-assembly to the vehicle body with the 2 nuts and 2 bolts.

      Torque:
      Bolt
      19.1 N*m  { 195 kgf*cm, 14 ft.*lbf }
      Nut
      17.5 N*m  { 178 kgf*cm, 13 ft.*lbf }

      Note

      Check that the push rod cannot be turned 30° or more in order to confirm that the clevis is securely engaged in the pedal.

  9. INSTALL CLUTCH PEDAL SWITCH ASSEMBLY

    Click here

  10. INSTALL NO. 2 CLUTCH PEDAL SWITCH ASSEMBLY

    Click here

  11. CONNECT CONNECTORS

    Click here

  12. INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY

    Click here

  13. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Instrument Panel Under Cover)


  14. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY (for Hatchback, Wagon)

    Click here

  15. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY (for Sedan)

    Click here

  16. INSPECT CLUTCH PEDAL SWITCH ASSEMBLY

    Click here