ULTRASONIC SENSOR(for Sedan Rear Side) INSTALLATION

PROCEDURE


  1. INSTALL REAR CENTER ULTRASONIC SENSOR

    Tech Tips


    • Perform this step only when necessary.

    • If a rear center ultrasonic sensor retainer has been removed, replace it with a new one.

    • Use the same procedure for all rear center ultrasonic sensor retainers, ultrasonic sensor clips and rear center ultrasonic sensors.


    1. When replacing the rear center ultrasonic sensor retainer:


      1. Clean the rear bumper assembly surface.


        1. Remove the double-sided tape from the rear bumper assembly.

        2. Wipe off any tape adhesive residue with cleaner.

      2. A01T9J8C01
        *a 19 mm (0.748 in.)

        Cover the sensor installation hole with a 19 mm (0.748 in.) circular piece of tape.

      3. Using a brush or felt, apply primer or equivalent to the rear center ultrasonic sensor retainer installation area.

        Note


        • Use a clean brush or felt.

        • Do not touch the rear bumper assembly until the primer has dried.

      4. Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.

      5. A01TAWC

        Engage the 2 claws to install the ultrasonic sensor clip to a new rear center ultrasonic sensor retainer.

      6. A01TDEH

        Engage the 2 claws to install the rear center ultrasonic sensor to the rear center ultrasonic sensor retainer and ultrasonic sensor clip.

      7. Peel off the release paper from the rear center ultrasonic sensor retainer.

      8. A01T8JXC01
        *a Scribed Line

        Align the rear center ultrasonic sensor retainer, ultrasonic sensor clip and rear center ultrasonic sensor with the scribed line on the rear bumper assembly and install it as shown in the illustration.

        Note


        • Insert the sensor tip into the sensor installation hole of the rear bumper assembly.

        • Ensure that the rear center ultrasonic sensor retainer is within the scribed line.

        • The double-sided tape of a rear center ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the rear center ultrasonic sensor retainer with a new one when reattachment is necessary.

        Tech Tips

        Press the rear center ultrasonic sensor retainer with a force of 30 N (3.0 kgf) for 3 seconds and install the rear center ultrasonic sensor retainer firmly so that there is no clearance between the rear center ultrasonic sensor retainer and rear bumper assembly.

    2. When replacing only the rear center ultrasonic sensor:


      1. A01TCX9

        Engage the 2 claws to install the rear center ultrasonic sensor.

    3. Connect the connector.

    4. Engage the clamp.

  2. INSTALL REAR CORNER ULTRASONIC SENSOR

    Tech Tips


    • Perform this step only when necessary.

    • If a rear corner ultrasonic sensor retainer has been removed, replace it with a new one.

    • Use the same procedure for all rear corner ultrasonic sensor retainers, ultrasonic sensor clips and rear corner ultrasonic sensors.


    1. When replacing the rear corner ultrasonic sensor retainer:


      1. Clean the rear bumper assembly surface.


        1. Remove the double-sided tape from the rear bumper assembly.

        2. Wipe off any tape adhesive residue with cleaner.

      2. A01T9J8C01
        *a 19 mm (0.748 in.)

        Cover the sensor installation hole with a 19 mm (0.748 in.) circular piece of tape.

      3. Using a brush or felt, apply primer or equivalent to the rear corner ultrasonic sensor retainer installation area.

        Note


        • Use a clean brush or felt.

        • Do not touch the rear bumper assembly until the primer has dried.

      4. Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.

      5. A01T8MK

        Engage the 2 claws to install the ultrasonic sensor clip to a new rear corner ultrasonic sensor retainer.

      6. A01T94K

        Engage the 2 claws to install the rear corner ultrasonic sensor to the rear corner ultrasonic sensor retainer and ultrasonic sensor clip.

      7. Peel off the release paper from the rear corner ultrasonic sensor retainer.

      8. A01TDDFC01
        *a Scribed Line

        Align the rear corner ultrasonic sensor retainer, ultrasonic sensor clip and rear corner ultrasonic sensor with the scribed line on the rear bumper assembly and install it as shown in the illustration.

        Note


        • Insert the sensor tip into the sensor installation hole of the rear bumper assembly.

        • Ensure that the rear corner ultrasonic sensor retainer is within the scribed line.

        • The double-sided tape of a rear corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the rear corner ultrasonic sensor retainer with a new one when reattachment is necessary.

        Tech Tips

        Press the rear corner ultrasonic sensor retainer with a force of 30 N (3.0 kgf) for 3 seconds and install the rear corner ultrasonic sensor retainer firmly so that there is no clearance between the rear corner ultrasonic sensor retainer and rear bumper assembly.

    2. When replacing only the rear corner ultrasonic sensor:


      1. A01TBLT

        Engage the 2 claws to install the rear corner ultrasonic sensor.

    3. Connect the connector.

    4. Engage the clamp.

  3. INSTALL REAR BUMPER ASSEMBLY

    Click here