FRONT DOOR LOCK(for Hatchback, Wagon) INSPECTION

PROCEDURE

1. INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

   
   
   1. 

      *a	Component without harness connected (Front Door Lock Assembly LH)
      *b	Unlock
      *c	Lock

      Check the operation of the front door lock motor.

      
      

      1. Apply battery voltage and check the operation of the front door lock motor.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL) Locks Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L) Unlocks

         If the result is not as specified, replace the front door lock assembly LH.

   2. 

      *a	Component without harness connected (Front Door Lock Assembly LH)
      *b	Unlock
      *c	Lock

      Check the operation of the door unlock detection switch. (w/ Entry and Start System)

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 7 (E) - 8 (LSSR) Locked 10 kΩ or higher Unlocked Below 1 Ω

         If the result is not as specified, replace the front door lock assembly LH.

   3. 

      *a	Component without harness connected (Front Door Lock Assembly LH)
      *b	Unlock
      *c	Lock

      Check the operation of the door key lock and unlock switch (for LHD).

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 9 (L) - 7 (E) Held to lock side Below 1 Ω 9 (L) - 7 (E) Neutral or held to unlock side 10 kΩ or higher 10 (UL) - 7 (E) Held to unlock side Below 1 Ω 10 (UL) - 7 (E) Neutral or held to lock side 10 kΩ or higher

         If the result is not as specified, replace the front door lock assembly LH.

2. INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

   
   
   1. 

      *a	Component without harness connected (Front Door Lock Assembly LH)
      *b	Unlock
      *c	Lock

      Check the operation of the front door lock motor.

      
      

      1. Apply battery voltage and check the operation of the front door lock motor and double lock motor.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 4 (L) Battery negative (-) → 3 (UL) Locks Battery positive (+) → 3 (UL) Battery negative (-) → 4 (L) Unlocks Battery positive (+) → 2 (DL) Battery negative (-) → 1 (UNDL) Sets Battery positive (+) → 1 (UNDL) Battery negative (-) → 2 (DL) Unsets

         Tech Tips

         
         

         • Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

         • Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

         If the result is not as specified, replace the front door lock assembly LH.

   2. 

      *a	Component without harness connected (Front Door Lock Assembly LH)
      *b	Unlock
      *c	Lock

      Check the operation of the door unlock detection switch and double lock position switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 8 (LSSR) - 7 (E) Locked 10 kΩ or higher 8 (LSSR) - 7 (E) Unlocked Below 1 Ω 6 (DLSR) - 5 (E) Unset 10 kΩ or higher 6 (DLSR) - 5 (E) Set Below 1 Ω

         If the result is not as specified, replace the front door lock assembly LH.

3. INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

   
   
   1. 

      *a	Component without harness connected (Front Door Lock Assembly RH)
      *b	Unlock
      *c	Lock

      Check the operation of the front door lock motor.

      
      

      1. Apply battery voltage and check the operation of the front door lock motor.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL) Locks Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L) Unlocks

         If the result is not as specified, replace the front door lock assembly RH.

   2. 

      *a	Component without harness connected (Front Door Lock Assembly RH)
      *b	Unlock
      *c	Lock

      Check the operation of the door unlock detection switch. (w/ Entry and Start System)

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 7 (LSSR) - 8 (E) Locked 10 kΩ or higher 7 (LSSR) - 8 (E) Unlocked Below 1 Ω

         If the result is not as specified, replace the front door lock assembly RH.

   3. 

      *a	Component without harness connected (Front Door Lock Assembly RH)
      *b	Unlock
      *c	Lock

      Check the operation of the door key lock and unlock switch (for RHD).

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 6 (L) - 8 (E) Held to lock side Below 1 Ω 6 (L) - 8 (E) Neutral or held to unlock side 10 kΩ or higher 5 (UL) - 8 (E) Held to unlock side Below 1 Ω 5 (UL) - 8 (E) Neutral or held to lock side 10 kΩ or higher

         If the result is not as specified, replace the front door lock assembly RH.

4. INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

   
   
   1. 

      *a	Component without harness connected (Front Door Lock Assembly RH)
      *b	Unlock
      *c	Lock

      Check the operation of the front door lock motor.

      
      

      1. Apply battery voltage and check the operation of the front door lock motor and double lock motor.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 2 (L) Battery negative (-) → 1 (UL) Locks Battery positive (+) → 1 (UL) Battery negative (-) → 2 (L) Unlocks Battery positive (+) → 4 (DL) Battery negative (-) → 3 (UNDL) Sets Battery positive (+) → 3 (UNDL) Battery negative (-) → 4 (DL) Unsets

         Tech Tips

         
         

         • Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

         • Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

         If the result is not as specified, replace the front door lock assembly RH.

   2. 

      *a	Component without harness connected (Front Door Lock Assembly RH)
      *b	Unlock
      *c	Lock

      Check the operation of the door unlock detection switch and double lock position switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 7 (LSSR) - 8 (E) Locked 10 kΩ or higher 7 (LSSR) - 8 (E) Unlocked Below 1 Ω 9 (DLSR) - 10 (E) Unset 10 kΩ or higher 9 (DLSR) - 10 (E) Set Below 1 Ω

         If the result is not as specified, replace the front door lock assembly RH.

   3. 

      *a	Component without harness connected (Front Door Lock Assembly RH)
      *b	Unlock
      *c	Lock

      Check the operation of the door key lock and unlock switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 6 (L) - 8 (E) Held to lock side Below 1 Ω 6 (L) - 8 (E) Neutral or held to unlock side 10 kΩ or higher 5 (UL) - 8 (E) Held to unlock side Below 1 Ω 5 (UL) - 8 (E) Neutral or held to lock side 10 kΩ or higher

         If the result is not as specified, replace the front door lock assembly RH.