EXHAUST GAS TEMPERATURE SENSOR(w/ Glow Plug Controller) COMPONENTS
ILLUSTRATION
| *A | w/ No. 1 Engine Cover | - | - |
| *1 | NO. 1 ENGINE COVER | - | - |
ILLUSTRATION
| *A | for LHD | *B | for RHD |
| *1 | NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL | *2 | OUTER COWL TOP PANEL |
| *3 | WATER GUARD PLATE LH | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | DIFFERENTIAL PRESSURE SENSOR ASSEMBLY | *2 | WIRE HARNESS CLAMP BRACKET |
| *3 | NO. 1 VACUUM TRANSMITTING HOSE ASSEMBLY | *4 | NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY |
| *5 | NO. 1 WIRE HARNESS HEAT INSULATOR | *6 | NO. 2 WIRE HARNESS HEAT INSULATOR |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | EXHAUST GAS TEMPERATURE SENSOR | *2 | WIRING HARNESS CLAMP BRACKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | * | For use with union nut wrench |
ILLUSTRATION
| *1 | NO. 2 ENGINE COVER BRACKET | *2 | SENSOR BRACKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for LHD | *B | for RHD |
| *1 | NO. 2 HOSE TO HOSE TUBE | *2 | CHECK VALVE TO CONNECTOR TUBE HOSE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | AIR CLEANER CAP SUB-ASSEMBLY | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | BATTERY | *4 | NO. 1 AIR TUBE |
| *5 | OUTLET HEATER WATER HOSE A | *6 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| *7 | BATTERY CLAMP SUB-ASSEMBLY | *8 | BATTERY CLAMP BOLT |
| *9 | BATTERY TRAY | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | NO. 1 TURBO INSULATOR | *2 | NO. 5 MANIFOLD SUPPORT BRACKET |
| *3 | NO. 2 VACUUM PIPE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | * | For use with union nut wrench |
ILLUSTRATION
| *A | Type A | *B | Type B |
| *1 | FRONT NO. 1 FLOOR HEAT INSULATOR | *2 | FRONT EXHAUST PIPE ASSEMBLY |
| *3 | FRONT CENTER FLOOR BRACE SUB-ASSEMBLY | *4 | EXHAUST PIPE SUPPORT |
| *5 | COMPRESSION SPRING | *6 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | NO. 4 MANIFOLD SUPPORT BRACKET | *2 | DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY |
| *3 | NO. 1 MANIFOLD SUPPORT BRACKET | *4 | OUTLET TURBINE ELBOW GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | * | For use with offset wrench and hexagon socket wrench |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *1 | NO. 1 VACUUM PIPE | *2 | NO. 2 EXHAUST GAS TEMPERATURE SENSOR |
| *3 | NO. 2 EXHAUST MANIFOLD | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | * | For use with union nut wrench |