MONOLITHIC CONVERTER(w/o Glow Plug Controller) REMOVAL

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE NO. 1 ENGINE COVER (w/ No. 1 Engine Cover)

    Click here

  4. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

    Click here

  5. REMOVE WATER GUARD PLATE LH (for LHD)

    Click here

  6. REMOVE WATER GUARD PLATE LH (for RHD)

    Click here

  7. REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for LHD)

    Click here

  8. REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for RHD)

    Click here

  9. REMOVE OUTER COWL TOP PANEL

    Click here

  10. REMOVE BATTERY

    Click here

  11. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

    Click here

  12. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  13. REMOVE NO. 1 AIR TUBE

    Click here

  14. REMOVE FRONT CENTER FLOOR BRACE SUB-ASSEMBLY

    Click here

  15. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    1. A00Y7QC

      Remove the 4 bolts and 4 compression springs.

    2. Remove the front exhaust pipe assembly from the 2 exhaust pipe supports.

    3. Remove the 2 gaskets from the front exhaust pipe assembly and No. 2 exhaust manifold converter sub-assembly.

  16. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

    Click here

  17. REMOVE HARNESS BRACKET

    Click here

  18. REMOVE NO. 1 TURBO INSULATOR


    1. A00Y6GAC01
      *1 Vacuum Transmitting Hose Assembly
      *2 No. 2 Vacuum Transmitting Hose Assembly

      Slide the 2 clips and disconnect the vacuum transmitting hose assembly and No. 2 vacuum transmitting hose assembly remove the differential pressure sensor assembly.

    2. A00YBH8

      Remove the 3 bolts and No. 1 turbo insulator.

  19. REMOVE AIR FUEL RATIO SENSOR

    Click here

  20. REMOVE NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY


    1. A00Y673

      Slide the clip and remove the No. 2 vacuum transmitting hose assembly from the No. 2 vacuum pipe.

  21. REMOVE VACUUM TRANSMITTING HOSE ASSEMBLY


    1. A00Y799

      Slide the clip and remove the vacuum transmitting hose assembly from the No. 1 vacuum pipe.

  22. REMOVE NO. 2 VACUUM PIPE


    1. A00Y8UY

      Remove the 2 bolts.

    2. Using a 14 mm union nut wrench, remove the No. 2 vacuum pipe.

  23. REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY


    1. A00Y9TP

      Remove the 2 nuts and drive shaft heat insulator sub-assembly from the manifold support bracket.

  24. REMOVE NO. 4 MANIFOLD SUPPORT BRACKET


    1. A00Y832

      Remove the 3 bolts and No. 4 manifold support bracket from the No. 1 converter support bracket and No. 2 exhaust manifold converter sub-assembly.

  25. REMOVE NO. 3 MANIFOLD SUPPORT BRACKET


    1. A00Y569

      Remove the 3 bolts and No. 3 manifold support bracket from the No. 2 manifold support bracket and No. 2 exhaust manifold converter sub-assembly.

  26. REMOVE NO. 2 EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY


    1. A00Y6I0

      Remove the 2 nuts and No. 2 exhaust manifold converter sub-assembly from the exhaust manifold converter sub-assembly.

    2. Remove the gasket from the exhaust manifold converter sub-assembly.

  27. REMOVE NO. 1 VACUUM PIPE


    1. Remove the bolt.

    2. A00Y7BM

      Using a 14 mm union nut wrench, remove the No. 1 vacuum pipe from the exhaust manifold converter sub-assembly.

  28. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY


    1. A00Y5OT

      Disengage the 2 wire harness clamps from the wire harness bracket.

    2. A00Y7IA

      Remove the bolt and harness bracket.

    3. A00YAC5C01
      *1 Exhaust Gas Temperature Sensor Connector
      *2 No. 2 Exhaust Gas Temperature Sensor Connector

      Disconnect the exhaust gas temperature sensor connector and No. 2 exhaust gas temperature sensor connector.

    4. Disengage the 2 wire harness clamps from the wire harness bracket and cylinder block side cover.

    5. A00Y5KOC01
      *1 Exhaust Gas Temperature Sensor Connector
      *2 No. 2 Exhaust Gas Temperature Sensor Connector

      Separate the exhaust gas temperature sensor connector and No. 2 exhaust gas temperature sensor connector from the wire harness bracket.

    6. Remove the bolt and wire harness bracket.

    7. A00Y8CJC01
      A00Y51D Bolt
      A00YA05 Nut

      Remove the bolt, 3 nuts and exhaust manifold converter sub-assembly.

    8. A00Y7BB

      Remove the gasket from the turbocharger sub-assembly.

  29. REMOVE EXHAUST GAS TEMPERATURE SENSOR

    Click here

  30. REMOVE NO. 2 EXHAUST GAS TEMPERATURE SENSOR

    Click here