FUEL INJECTOR INSTALLATION

PROCEDURE


  1. INSTALL FUEL INJECTOR ASSEMBLY

    Tech Tips

    Perform "Inspection After Repair" after replacing the fuel injector assembly.

    Click here


    1. B0043PLC01
      *1 O-ring
      *2 Injector Vibration Insulator

      Apply a light coat of gasoline or spindle oil to new injector vibration insulators and O-rings, and then install one onto each fuel injector assembly.

    2. Apply a light coat of gasoline or spindle oil where the fuel delivery pipe sub-assembly contacts each O-ring.

    3. B00436T

      While turning the fuel injector assembly left and right, install it onto the fuel delivery pipe sub-assembly.

      Note


      • Do not damage the fuel injector assembly or O-ring.

      • Do not twist the O-ring.

      • After installing each fuel injector assembly, check that it turns smoothly. If not, replace the O-ring with a new one.

  2. INSTALL NO. 1 DELIVERY PIPE SPACER


    1. B0044RLC01
      *a Fuel Delivery Pipe Sub-assembly Side
      *b Cylinder Head Side

      Install the 2 No. 1 delivery pipe spacers onto the cylinder head.

      Note

      Install the No. 1 delivery pipe spacers in the correct direction.

  3. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY


    1. Install the fuel delivery pipe sub-assembly with fuel injector assemblies with the 2 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

      Note


      • Do not drop the fuel injector assemblies when installing the fuel delivery pipe sub-assembly.

      • After installing the fuel delivery pipe sub-assembly, check that the fuel injector assemblies turn smoothly.

    2. Install the fuel delivery pipe sub-assembly to the cylinder head sub-assembly with the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    3. Install the wire harness bracket to the intake manifold with the engine cover joint.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  4. CONNECT FUEL TUBE SUB-ASSEMBLY


    1. B0042I4C04
      *1 Fuel Delivery Pipe Sub-assembly
      *a Retainer
      *b O-ring

      Connect the fuel tube sub-assembly connector to the fuel delivery pipe sub-assembly until a "click" sound is heard.

      Note


      • Check that there are no scratches or foreign matter on the contact surfaces of the fuel tube sub-assembly connector and fuel delivery pipe sub-assembly before performing this work.

      • After connecting the fuel lines, check that the fuel tube sub-assembly connector and fuel delivery pipe sub-assembly are securely connected by pulling on them.

    2. B00445U

      Type A:


      1. Install a new No. 2 fuel pipe clamp.

    3. B0044N0C01
      *a Claw

      Type B:


      1. Install a new No. 2 fuel pipe clamp.

  5. INSTALL VACUUM SURGE TANK

    Click here

  6. CONNECT ENGINE WIRE


    1. Connect the engine wire and install the 3 bolts and 3 nuts as shown in the illustration.

      B0042N7N01
      Torque:
      Bolt (A)
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
      Bolt (B)
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
      Nut
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      Tech Tips

      It is acceptable for the ground wires to be tilted +20° to -20°.

    2. Engage the 7 clamps, and then connect the 20 connectors.

  7. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  8. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

    Click here

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  10. INSPECT FOR FUEL LEAK

    Click here

  11. INSTALL NO. 2 CYLINDER HEAD COVER

    Click here