FUEL INJECTOR REMOVAL

CAUTION / NOTICE / HINT

Note

When replacing the injector assemblies (including exchanging the injector assemblies between the cylinders), common rail assembly, intake manifold or cylinder head, it is necessary to replace the injection pipe sub-assemblies with new ones.

Tech Tips

After replacing any of the injector assemblies, perform both the "Injector Compensation" and the "Pilot Quantity Learning Values Reset" functions using the GTS.

Click here

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

    Click here

  4. REMOVE WATER GUARD PLATE LH (for Sedan)

    Click here

  5. REMOVE WATER GUARD PLATE LH (for Hatchback, Wagon)

    Click here

  6. REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for Sedan)

    Click here

  7. REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for Hatchback, Wagon)

    Click here

  8. SEPARATE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

    Click here

  9. REMOVE OUTER COWL TOP PANEL (for Sedan)

    Click here

  10. REMOVE OUTER COWL TOP PANEL (for Hatchback, Wagon)

    Click here

  11. REMOVE NO. 1 ENGINE COVER

    Click here

  12. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

    Click here

  13. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  14. SEPARATE ENGINE WIRE


    1. A012I1G

      Disconnect the 4 connectors from the 4 injector assemblies.

    2. A012NF5

      Disconnect the 3 connectors.

    3. A012G6Y

      Disconnect the connector from the fuel pressure sensor.

    4. Disconnect the connector from the pressure control valve.

    5. Disconnect the glow plug connector.

    6. Disengage the 2 wire harness clamps.

    7. Remove the 2 bolts and 2 wire harness brackets.

    8. Remove the bolt and 5 nuts and disconnect the engine wire.

  15. REMOVE INJECTION PIPE SUB-ASSEMBLY

    Note

    After removing the injection pipe sub-assembly, cover the common rail assembly with protective tape to prevent dirt or foreign matter from entering the pipe inlet. Also protect the injector inlets by covering them with protective tape or plastic bags.


    1. A012FXX

      Remove the 2 bolts and 4 injection pipe clamps.

    2. Using a 14 mm union nut wrench, loosen the 4 nuts at the common rail assembly end of the injection pipe sub-assemblies.

    3. Using a 14 mm union nut wrench, loosen the 4 nuts at the injector end of the injection pipe sub-assemblies.

    4. Remove the 4 injection pipe sub-assemblies.

  16. REMOVE FUEL HOSE PROTECTOR

    Click here

  17. REMOVE FUEL TUBE SUB-ASSEMBLY

    Click here

  18. REMOVE NO. 2 NOZZLE LEAKAGE PIPE


    1. A012FNM

      Slide the 3 clips and disconnect the 3 fuel hoses.

    2. A012H0K

      Remove the check valve.

    3. Remove the bolt and No. 2 nozzle leakage pipe with the gasket.

  19. REMOVE NO. 1 NOZZLE LEAKAGE PIPE


    1. A012HCS

      Remove the 4 union bolts.

    2. Remove the bolt and No. 1 nozzle leakage pipe with the 4 gaskets.

  20. REMOVE NO. 1 NOZZLE HOLDER CLAMP


    1. A012M8P

      Remove the 4 bolts, 4 washers and 4 No. 1 nozzle holder clamps.

  21. REMOVE INJECTOR ASSEMBLY


    1. Remove the 4 injector assemblies and 4 injection nozzle seats from the cylinder head.

      Note

      Arrange the removed parts in the correct order so that they can be returned to their original locations when reassembling.

    2. Remove the O-rings from each injector assembly.