ENGINE UNIT COMPONENTS
ILLUSTRATION
| *A | Type A | *B | Type B |
| *1 | FUEL DELIVERY PIPE SUB-ASSEMBLY | *2 | FUEL INJECTOR ASSEMBLY |
| *3 | FUEL TUBE SUB-ASSEMBLY | *4 | THERMOSTAT |
| *5 | VACUUM SURGE TANK | *6 | WATER INLET |
| *7 | GASKET | *8 | NO. 1 DELIVERY PIPE SPACER |
| *9 | O-RING | *10 | INJECTOR VIBRATION INSULATOR |
| *11 | NO. 2 FUEL PIPE CLAMP | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | Type A | *B | Type B |
| *1 | EXHAUST MANIFOLD | *2 | IGNITION COIL ASSEMBLY |
| *3 | NO. 1 EXHAUST MANIFOLD HEAT INSULATOR | *4 | EXHAUST MANIFOLD TO HEAD GASKET |
| *5 | MANIFOLD STAY | *6 | DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY |
| *a | Diameter 18 mm (0.709 in.) | *b | Diameter 17 mm (0.669 in.) |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | ENGINE OIL LEVEL DIPSTICK GUIDE | *2 | INTAKE MANIFOLD |
| *3 | NO. 1 WATER BY-PASS PIPE | *4 | NO. 3 WATER BY-PASS HOSE |
| *5 | VENTILATION HOSE | *6 | WATER BY-PASS HOSE |
| *7 | WATER INLET HOSE | *8 | ENGINE OIL LEVEL DIPSTICK |
| *9 | AIR TUBE | *10 | NO. 1 INTAKE MANIFOLD TO HEAD GASKET |
| *11 | INTAKE MANIFOLD STAY | *12 | O-RING |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAMSHAFT POSITION SENSOR | *2 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
| *3 | CYLINDER HEAD COVER GASKET | *4 | CYLINDER HEAD COVER SUB-ASSEMBLY |
| *5 | ENGINE COVER JOINT | *6 | OIL FILLER CAP GASKET |
| *7 | OIL FILLER CAP SUB-ASSEMBLY | *8 | SPARK PLUG |
| *9 | SPARK PLUG TUBE GASKET | *10 | SEAL WASHER |
| *11 | GASKET | *12 | O-RING |
| *13 | BRACKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CRANKSHAFT PULLEY | *2 | ENGINE OIL PRESSURE SWITCH ASSEMBLY |
| *3 | NO. 1 CHAIN TENSIONER ASSEMBLY | *4 | OIL FILTER CAP ASSEMBLY |
| *5 | TIMING CHAIN COVER OIL SEAL | *6 | TIMING CHAIN COVER SUB-ASSEMBLY |
| *7 | WATER INLET HOUSING | *8 | ENGINE MOUNTING BRACKET RH |
| *9 | GASKET | *10 | OIL FILTER BRACKET |
| *11 | OIL FILTER ELEMENT | *12 | O-RING |
| *13 | ENGINE WATER PUMP ASSEMBLY | *14 | SEAL WASHER |
| *15 | STUD BOLT | *16 | BRACKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
MP grease | ★ | Precoated part |
ILLUSTRATION
| *1 | CHAIN SUB-ASSEMBLY | *2 | CHAIN TENSIONER SLIPPER |
| *3 | CRANKSHAFT POSITION SENSOR | *4 | CRANKSHAFT TIMING GEAR KEY |
| *5 | CRANKSHAFT TIMING SPROCKET | *6 | NO. 1 CHAIN VIBRATION DAMPER |
| *7 | NO. 1 CRANKSHAFT POSITION SENSOR PLATE | *8 | NO. 2 CHAIN SUB-ASSEMBLY |
| *9 | NO. 2 CHAIN VIBRATION DAMPER | *10 | O-RING |
| *11 | OIL PUMP DRIVE GEAR | *12 | OIL PUMP DRIVE SHAFT GEAR |
| *13 | CHAIN DAMPER SPRING | *14 | CHAIN TENSIONER PLATE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAMSHAFT | *2 | CAMSHAFT BEARING CAP |
| *3 | CAMSHAFT HOUSING SUB-ASSEMBLY | *4 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
| *5 | CAMSHAFT TIMING GEAR ASSEMBLY | *6 | CYLINDER HEAD GASKET |
| *7 | CYLINDER HEAD SUB-ASSEMBLY | *8 | ENGINE COOLANT TEMPERATURE SENSOR |
| *9 | NO. 1 CAMSHAFT BEARING | *10 | NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
| *11 | NO. 2 CAMSHAFT | *12 | NO. 2 CAMSHAFT BEARING |
| *13 | OIL CONTROL VALVE FILTER | *14 | VALVE LASH ADJUSTER ASSEMBLY |
| *15 | PLATE WASHER | *16 | CYLINDER HEAD SET BOLT |
| *17 | GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *T1 | 1st: 49 (500, 36) 2nd: Turn 90° 3rd: Turn 45° |
- | - |
ILLUSTRATION
| *1 | KNOCK CONTROL SENSOR | *2 | NO. 1 GENERATOR BRACKET |
| *3 | NO. 1 TAPER SCREW PLUG | *4 | NO. 2 OIL PAN SUB-ASSEMBLY |
| *5 | OIL PAN DRAIN PLUG | *6 | OIL PUMP ASSEMBLY |
| *7 | REAR ENGINE OIL SEAL | *8 | STIFFENING CRANKCASE ASSEMBLY |
| *9 | PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY) | *10 | RING PIN |
| *11 | STUD BOLT | *12 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | ★ | Precoated part |