ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | FRONT LOWER BUMPER ABSORBER | *2 | NO. 1 ENGINE UNDER COVER |
| *3 | NO. 2 ENGINE UNDER COVER | *4 | REAR ENGINE UNDER COVER LH |
| *5 | REAR ENGINE UNDER COVER RH | - | - |
ILLUSTRATION
| *1 | AIR CLEANER CAP SUB-ASSEMBLY | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | BATTERY | *4 | BATTERY CARRIER ASSEMBLY |
| *5 | NO. 2 CYLINDER HEAD COVER | *6 | BATTERY CLAMP SUB-ASSEMBLY |
| *7 | BATTERY TRAY | *8 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| *9 | RADIATOR PIPE | *10 | BATTERY CLAMP BOLT |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FUEL TUBE SUB-ASSEMBLY | *2 | INLET HEATER WATER HOSE |
| *3 | NO. 1 FUEL VAPOR FEED HOSE | *4 | NO. 1 RADIATOR HOSE |
| *5 | NO. 2 RADIATOR HOSE | *6 | OUTLET HEATER WATER HOSE |
| *7 | UNION TO VACUUM TUBE HOSE | *8 | NO. 1 FUEL PIPE CLAMP |
| *9 | FUEL PIPE | *10 | BREATHER PLUG HOSE |
ILLUSTRATION
| *1 | COLUMN HOLE COVER SILENCER SHEET | *2 | GENERATOR ASSEMBLY |
| *3 | NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY | *4 | V-RIBBED BELT |
| *5 | ADJUSTING BAR | *6 | TERMINAL CAP |
| *7 | WIRE HARNESS CLAMP BRACKET | *8 | NO. 1 ENGINE ROOM RELAY BLOCK COVER |
| *9 | WIRE HARNESS | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | COMPRESSOR ASSEMBLY WITH PULLEY | *2 | DISCHARGE HOSE SUB-ASSEMBLY |
| *3 | SUCTION HOSE SUB-ASSEMBLY | *4 | O-RING |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
for HFC-134a (R134a): Compressor oil ND-OIL 8 or equivalent for HFO-1234yf (R1234yf): Compressor oil ND-OIL 12 or equivalent |
- | - |
ILLUSTRATION
| *1 | FRONT ENGINE MOUNTING INSULATOR | *2 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
| *3 | NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY | *4 | REAR ENGINE MOUNTING INSULATOR |
| *5 | TRANSMISSION CONTROL CABLE ASSEMBLY | *6 | FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT |
| *7 | FRONT SUSPENSION MEMBER REAR BRACE LH | *8 | FRONT SUSPENSION MEMBER REAR BRACE RH |
| *9 | FRONT SUSPENSION MEMBER REINFORCEMENT LH | *10 | FRONT SUSPENSION MEMBER REINFORCEMENT RH |
| *11 | FRONT CROSSMEMBER SUB-ASSEMBLY | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque |  |
Do not apply lubricants |
ILLUSTRATION
| *1 | ENGINE MOUNTING INSULATOR LH | *2 | ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
| *3 | ENGINE WIRE | *4 | COOLER PIPE CLAMP BRACKET |
| *5 | RADIATOR RESERVOIR TANK | *6 | WIRE HARNESS CLAMP BRACKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY | *2 | DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
| *3 | DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT | *4 | FLYWHEEL HOUSING SIDE COVER |
| *5 | FLYWHEEL HOUSING UNDER COVER | *6 | STARTER ASSEMBLY |
| *7 | TRANSMISSION CONTROL CABLE ASSEMBLY | *8 | NO. 5 WATER BY-PASS HOSE |
| *9 | FRONT DRIVE PLATE SPACER | *10 | REAR DRIVE PLATE SPACER |
| *11 | GROUND WIRE | - | - |
| *a | BLACK: x 1 SILVER: x 5 |
- | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| ★ | Precoated part | - | - |