ENGINE UNIT COMPONENTS
ILLUSTRATION
| *A | w/ Stud Bolt | *B | w/o Stud Bolt |
| *1 | DUTY VACUUM SWITCHING VALVE | *2 | FUEL DELIVERY PIPE SUB-ASSEMBLY |
| *3 | FUEL INJECTOR ASSEMBLY | *4 | FUEL TUBE SUB-ASSEMBLY |
| *5 | INTAKE MANIFOLD | *6 | NO. 1 DELIVERY PIPE SPACER |
| *7 | THROTTLE BODY ASSEMBLY | *8 | WIRE HARNESS CLAMP BRACKET |
| *9 | INTAKE MANIFOLD STAY | *10 | INJECTOR VIBRATION INSULATOR |
| *11 | NO. 2 FUEL PIPE CLAMP | *12 | O-RING |
| *13 | NO. 1 WATER BY-PASS HOSE | *14 | NO. 2 WATER BY-PASS HOSE |
| *15 | THROTTLE BODY GASKET | *16 | NO. 1 INTAKE MANIFOLD TO HEAD GASKET |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | Type A | *B | Type B |
| *C | Type C | - | - |
| *1 | EXHAUST MANIFOLD | *2 | MANIFOLD STAY |
| *3 | NO. 1 EXHAUST MANIFOLD HEAT INSULATOR | *4 | EXHAUST MANIFOLD TO HEAD GASKET |
| *a | 18 mm (0.709 in.) | *b | 17 mm (0.669 in.) |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | VACUUM PUMP ASSEMBLY | *2 | UNION TO CONNECTOR TUBE HOSE |
| *3 | O-RING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for CVT | *B | for Manual Transaxle |
| *1 | ENGINE OIL LEVEL DIPSTICK GUIDE | *2 | IGNITION COIL ASSEMBLY |
| *3 | NO. 1 VACUUM PUMP BRACKET | *4 | NO. 1 WATER BY-PASS PIPE |
| *5 | NO. 3 WATER BY-PASS HOSE | *6 | VENTILATION HOSE |
| *7 | WATER BY-PASS HOSE | *8 | WATER INLET HOSE |
| *9 | ENGINE OIL LEVEL DIPSTICK | *10 | O-RING |
| *11 | GASKET | *12 | WIRE HARNESS CLAMP BRACKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAMSHAFT POSITION SENSOR | *2 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
| *3 | CYLINDER HEAD COVER GASKET | *4 | CYLINDER HEAD COVER SUB-ASSEMBLY |
| *5 | ENGINE COVER JOINT | *6 | OIL FILLER CAP GASKET |
| *7 | OIL FILLER CAP SUB-ASSEMBLY | *8 | SPARK PLUG |
| *9 | SPARK PLUG TUBE GASKET | *10 | SEAL WASHER |
| *11 | STUD BOLT | *12 | GASKET |
| *13 | O-RING | *14 | BRACKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CRANKSHAFT PULLEY | *2 | ENGINE OIL PRESSURE SWITCH ASSEMBLY |
| *3 | NO. 1 CHAIN TENSIONER ASSEMBLY | *4 | OIL FILTER CAP ASSEMBLY |
| *5 | THERMOSTAT | *6 | TIMING CHAIN COVER OIL SEAL |
| *7 | TIMING CHAIN COVER SUB-ASSEMBLY | *8 | WATER INLET |
| *9 | WATER INLET HOUSING | *10 | ENGINE MOUNTING BRACKET RH |
| *11 | ENGINE WATER PUMP ASSEMBLY | *12 | OIL FILTEREL EMENT |
| *13 | OIL FILTER BRACKET | *14 | BRACKET |
| *15 | GASKET | *16 | O-RING |
| *17 | SEAL WASHER | *18 | WATER INLET HOUSING STUD BOLT |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
MP grease | ★ | Precoated part |
 |
Do not apply lubricants to the threads | - | - |
ILLUSTRATION
| *1 | CHAIN SUB-ASSEMBLY | *2 | CHAIN TENSIONER SLIPPER |
| *3 | CRANKSHAFT POSITION SENSOR | *4 | CRANKSHAFT TIMING GEAR KEY |
| *5 | CRANKSHAFT TIMING SPROCKET | *6 | NO. 1 CHAIN VIBRATION DAMPER |
| *7 | NO. 1 CRANKSHAFT POSITION SENSOR PLATE | *8 | NO. 2 CHAIN SUB-ASSEMBLY |
| *9 | OIL PUMP DRIVE GEAR | *10 | OIL PUMP DRIVE SHAFT GEAR |
| *11 | CHAIN DAMPER SPRING | *12 | CHAIN TENSIONER PLATE |
| *13 | O-RING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAMSHAFT HOUSING SUB-ASSEMBLY | *2 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
| *3 | CAMSHAFT TIMING GEAR ASSEMBLY | *4 | CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY |
| *5 | CYLINDER HEAD SUB-ASSEMBLY | *6 | CYLINDER HEAD GASKET |
| *7 | ENGINE COOLANT TEMPERATURE SENSOR | *8 | VALVE ROCKER ARM LOST MOTION DAMPER SUB-ASSEMBLY |
| *9 | WIRE HARNESS CLAMP BRACKET | *10 | VALVE LIFT CONTROL ACTUATOR CONNECTOR |
| *11 | VALVE LIFT CONTROL ACTUATOR CLIP | *12 | PLATE WASHER |
| *13 | STRAIGHT PIN | *14 | O-RING |
| *15 | GASKET | *16 | CAMSHAFT HOUSING STUD BOLT |
| *17 | CAMSHAFT HOUSING STRAIGHT PIN | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *T1 | 1st: 49 (500, 36) 2nd: Turn 90° 3rd: Turn 45° |
- | - |
ILLUSTRATION
| *1 | REAR ENGINE OIL SEAL | *2 | KNOCK CONTROL SENSOR |
| *3 | NO. 1 GENERATOR BRACKET | *4 | NO. 1 TAPER SCREW PLUG |
| *5 | NO. 2 OIL PAN SUB-ASSEMBLY | *6 | OIL PAN DRAIN PLUG |
| *7 | OIL PUMP ASSEMBLY | *8 | STIFFENING CRANKCASE ASSEMBLY |
| *9 | VENTILATION VALVE SUB-ASSEMBLY | *10 | STIFFENING CRANKCASE RING PIN |
| *11 | STIFFENING CRANKCASE STUD BOLT | *12 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | ★ | Precoated part |