ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *A | for Half Cover Type | *B | for Full Cover Type |
| *C | w/ Cover | - | - |
| *1 | FRONT LOWER BUMPER ABSORBER | *2 | NO. 1 ENGINE UNDER COVER |
| *3 | CENTER NO. 4 ENGINE UNDER COVER | *4 | REAR ENGINE UNDER COVER LH |
| *5 | REAR ENGINE UNDER COVER RH | - | - |
ILLUSTRATION
| *1 | AIR CLEANER CAP WITH AIR CLEANER HOSE | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | NO. 1 ENGINE COVER SUB-ASSEMBLY | *4 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | w/ Air Conditioning System | - | - |
| *1 | DISCHARGE HOSE SUB-ASSEMBLY | *2 | FUEL TUBE SUB-ASSEMBLY |
| *3 | FUEL VAPOR FEED HOSE | *4 | NO. 1 RADIATOR HOSE |
| *5 | NO. 1 TURBO WATER HOSE | *6 | NO. 2 RADIATOR HOSE |
| *7 | NO. 4 TURBO WATER HOSE | *8 | SUCTION HOSE SUB-ASSEMBLY |
| *9 | UNION TO CONNECTOR TUBE HOSE | *10 | NO. 1 RELAY BLOCK COVER |
| *11 | O-RING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
for HFC-134a (R134a): Compressor oil ND-OIL 8 or equivalent for HFO-1234yf (R1234yf): Compressor oil ND-OIL 12 or equivalent |
- | - |
ILLUSTRATION
| *A | for CVT | *B | for Manual Transaxle |
| *1 | HEATER WATER INLET HOSE A | *2 | HEATER WATER OUTLET HOSE A |
| *3 | TRANSMISSION CONTROL CABLE ASSEMBLY | *4 | WATER HOSE |
| *5 | NO. 3 ENGINE WIRE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | Type A | *B | Type B |
| *1 | FRONT CENTER FLOOR BRACE SUB-ASSEMBLY | *2 | FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) |
| *3 | COMPRESSION SPRING | *4 | EXHAUST PIPE SUPPORT |
| *5 | EXHAUST PIPE GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for CVT | *B | for Manual Transaxle |
| *C | Type A | *D | Type B |
| *E | w/ Reinforcement | - | - |
| *1 | COLUMN HOLE COVER SILENCER SHEET | *2 | FRONT CROSSMEMBER SUB-ASSEMBLY |
| *3 | FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT | *4 | FRONT ENGINE MOUNTING INSULATOR |
| *5 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY | *6 | FRONT SUSPENSION MEMBER REAR BRACE LH |
| *7 | FRONT SUSPENSION MEMBER REAR BRACE RH | *8 | FRONT SUSPENSION MEMBER REINFORCEMENT LH |
| *9 | FRONT SUSPENSION MEMBER REINFORCEMENT RH | *10 | NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
| *11 | NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY | *12 | REAR ENGINE MOUNTING INSULATOR |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for CVT | *B | for Manual Transaxle |
| *C | w/ Air Conditioning System | *D | w/o Air Conditioning System |
| *1 | COMPRESSOR ASSEMBLY WITH PULLEY | *2 | ENGINE ASSEMBLY WITH TRANSAXLE |
| *3 | ENGINE MOUNTING INSULATOR LH | *4 | ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
| *5 | ENGINE WIRE | *6 | FLYWHEEL HOUSING UNDER COVER |
| *7 | GENERATOR ASSEMBLY | *8 | V-RIBBED BELT |
| *9 | V-RIBBED BELT TENSIONER ASSEMBLY | *10 | COOLER PIPE CLAMP BRACKET |
| *11 | TERMINAL CAP | *12 | INTERCOOLER RESERVE TANK ASSEMBLY |
| *13 | WIRE HARNESS CLAMP BRACKET | *14 | NO. 1 IDLER PULLEY |
| *15 | IDLER PULLEY BRACKET | *16 | IDLER PULLEY COVER PLATE |
| *17 | NO. 1 IDLER PULLEY SUB-ASSEMBLY | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for CVT | *B | for Transaxle CVT with Stop and Start System |
| *C | w/o Stop And Start System | - | - |
| *1 | CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY | *2 | DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
| *3 | DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT | *4 | FLYWHEEL HOUSING SIDE COVER |
| *5 | STARTER ASSEMBLY | *6 | TERMINAL CAP PROTECTOR |
| *7 | FRONT DRIVE PLATE SPACER | *8 | REAR DRIVE PLATE SPACER |
| *9 | ENGINE ASSEMBLY | *10 | TERMINAL CAP |
| *a | BLACK: x 1 SILVER: x 5 |
- | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | |
Adhesive 1324 |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *A | for Manual Transaxle | *B | for Transaxle M/T with Stop and Start System |
| *C | w/o Stop And Start System | - | - |
| *1 | CLUTCH HOSE | *2 | FLYWHEEL HOUSING SIDE COVER |
| *3 | FLYWHEEL SUB-ASSEMBLY | *4 | STARTER ASSEMBLY |
| *5 | TERMINAL CAP | *6 | ENGINE ASSEMBLY |
| *7 | BLEEDER CLUTCH RELEASE TUBE | *8 | TERMINAL CAP PROTECTOR |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | * | For use with a union nut wrench |
| ● | Non-reusable part | |
Adhesive 1324 |
| ★ | Precoated part | - | - |
| *T1 | 1st: 49 (500, 36) 2nd: Turn 90° |
- | - |