ENGINE UNIT COMPONENTS
ILLUSTRATION
| *1 | NO. 1 EXHAUST MANIFOLD HEAT INSULATOR | *2 | NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
| *3 | NO. 2 RADIATOR HOSE | *4 | EXHAUST MANIFOLD TO HEAD GASKET |
| *5 | INLET EGR GASKET | *6 | EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY(TWC: Front Catalyst) |
| *7 | MANIFOLD STAY | *8 | FUEL DELIVERY PIPE |
| *9 | O-RING | *10 | FUEL INJECTOR ASSEMBLY |
| *11 | FUEL DELIVERY SPACER | *12 | GASKET |
| *13 | WATER HOSE | *14 | EGR VALVE ASSEMBLY |
| *15 | EGR VALVE GASKET | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | NO. 1 IGNITION COIL | *2 | OIL LEVEL DIPSTICK SUB-ASSEMBLY |
| *3 | V-RIBBED BELT TENSIONER ASSEMBLY | *4 | VENTILATION HOSE |
| *5 | NO.1 WATER BY-PASS PIPE | *6 | OIL LEVEL DIPSTICK GUIDE SUB-ASSEMBLY |
| *7 | O-RING | *8 | STUD BOLT |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAMSHAFT POSITION SENSOR (for Exhaust Side) | *2 | OIL FILLER CAP SUB-ASSEMBLY |
| *3 | OIL FILLER CAP GASKET | *4 | VENTILATION VALVE SUB-ASSEMBLY |
| *5 | VENTILATION SYSTEM GROMMET | *6 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
| *7 | O-RING | *8 | SEAL WASHER |
| *9 | CYLINDER HEAD COVER SUB-ASSEMBLY | *10 | CYLINDER HEAD COVER GASKET |
| *11 | SPARK PLUG | *12 | CAMSHAFT BEARING CAP OIL HOLE GASKET |
| *13 | CAMSHAFT POSITION SENSOR (for Intake Side) | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Adhesive 1324 | ★ | Precoated part |
ILLUSTRATION
| *1 | ENGINE MOUNTING BRACKET RH | *2 | ENGINE OIL PRESSURE SWITCH ASSEMBLY |
| *3 | KNOCK CONTROL SENSOR | *4 | ENGINE COOLANT TEMPERATURE SENSOR |
| *5 | TIMING CHAIN COVER SUB-ASSEMBLY | *6 | PLUG |
| *7 | GASKET | *8 | CRANK POSITION SENSOR |
| *9 | SEAL WASHER | *10 | O-RING |
| *11 | TIMING CHAIN COVER OIL SEAL | *12 | CRANKSHAFT PULLEY |
| *13 | WATER INLET | *14 | THERMOSTAT |
| *15 | SPRING | *16 | FRAME |
| *17 | NO. 2 WATER INLET HOUSING GASKET | *18 | ENGINE WATER PUMP ASSEMBLY |
| *19 | ELEMENT | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | ★ | Precoated part |
ILLUSTRATION
| *1 | NO. 1 CHAIN TENSIONER ASSEMBLY | *2 | NO. 2 CHAIN VIBRATION DAMPER |
| *3 | GASKET | *4 | TIMING CHAIN GUIDE |
| *5 | TIMING CHAIN TENSION ARM | *6 | CHAIN SUB-ASSEMBLY |
| *7 | REAR ENGINE OIL SEAL | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAMSHAFT BEARING CAP | *2 | CAMSHAFT |
| *3 | CAMSHAFT TIMING GEAR ASSEMBLY | *4 | CYLINDER HEAD SUB-ASSEMBLY |
| *5 | CYLINDER BLOCK WATER JACKET SPACER | *6 | CYLINDER HEAD GASKET |
| *7 | VALVE LASH ADJUSTER ASSEMBLY | *8 | NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
| *9 | CAMSHAFT HOUSING SUB-ASSEMBLY | *10 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
| *11 | NO. 2 CAMSHAFT | *12 | PLATE WASHER |
| *13 | CYLINDER HEAD SET BOLT | *14 | RING PIN |
| *15 | OIL CONTROL VALVE FILTER | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *T1 | 1st: 32 (326, 24) 2nd: turn 90° 3rd: turn 90° |
- | - |
ILLUSTRATION
| *1 | CYLINDER BLOCK SUB-ASSEMBLY | *2 | NO. 1 OIL PAN BAFFLE PLATE |
| *3 | GASKET | *4 | OIL PAN DRAIN PLUG |
| *5 | O-RING | *6 | OIL FILTER DRAIN PLUG |
| *7 | OIL FILTER CAP | *8 | OIL FILTER ELEMENT |
| *9 | OIL PAN SUB-ASSEMBLY | *10 | OIL STRAINER SUB-ASSEMBLY |
| *11 | STRAIGHT PIN | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| ★ | Precoated part | - | - |