ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | AIR CLEANER CAP SUB-ASSEMBLY | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | BATTERY | *4 | FRONT LOWER BUMPER ABSORBER |
| *5 | NO. 1 ENGINE COVER | *6 | NO. 1 ENGINE UNDER COVER |
| *7 | NO. 1 RADIATOR HOSE | *8 | PURGE VALVE (PURGE VSV) |
| *9 | CENTER NO. 4 ENGINE UNDER COVER | *10 | REAR ENGINE UNDER COVER LH |
| *11 | REAR ENGINE UNDER COVER RH | *12 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| *13 | BATTERY CLAMP SUB-ASSEMBLY | *14 | BATTERY CLAMP BOLT |
| *15 | BATTERY TRAY | *16 | RADIATOR PIPE |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for LHD | *B | for RHD |
| *1 | CHECK VALVE TO BRAKE BOOSTER HOSE | *2 | FUEL TUBE SUB-ASSEMBLY |
| *3 | HEATER WATER INLET HOSE A | *4 | ENGINE WIRE |
| *5 | NO. 2 RADIATOR HOSE | *6 | HEATER WATER OUTLET HOSE A |
| *7 | UNION TO CONNECTOR TUBE HOSE | *8 | NO. 2 FUEL PIPE CLAMP |
| *9 | FUEL DELIVERY PIPE | *10 | NO. 1 RELAY BLOCK COVER |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | w/ Air Conditioning System | - | - |
| *1 | COLUMN HOLE COVER SILENCER SHEET | *2 | DISCHARGE HOSE SUB-ASSEMBLY |
| *3 | FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) | *4 | GENERATOR ASSEMBLY |
| *5 | NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY | *6 | SUCTION HOSE SUB-ASSEMBLY |
| *7 | V-RIBBED BELT | *8 | O-RING |
| *9 | GASKET | *10 | COMPRESSION SPRING |
| *11 | TERMINAL CAP | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Compressor oil ND-OIL 8 or equivalent | - | - |
ILLUSTRATION
| *A | Type A | *B | Type B |
| *C | Type C | *D | w/ Reinforcement |
| *1 | FRONT ENGINE MOUNTING INSULATOR | *2 | FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT |
| *3 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY | *4 | FRONT SUSPENSION MEMBER REAR BRACE LH |
| *5 | FRONT SUSPENSION MEMBER REAR BRACE RH | *6 | FRONT SUSPENSION MEMBER REINFORCEMENT LH |
| *7 | FRONT SUSPENSION MEMBER REINFORCEMENT RH | *8 | NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
| *9 | REAR ENGINE MOUNTING INSULATOR | *10 | TRANSMISSION CONTROL CABLE ASSEMBLY |
| *11 | FRONT CROSS MEMBER SUB-ASSEMBLY | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque |  |
Do not apply lubricants |
ILLUSTRATION
| *A | Type A | *B | Type B |
| *C | w/ Air Conditioning System | - | - |
| *1 | COMPRESSOR ASSEMBLY WITH PULLEY | *2 | ENGINE MOUNTING INSULATOR LH |
| *3 | ENGINE MOUNTING INSULATOR RH | *4 | ENGINE WIRE |
| *5 | COOLER PIPE CLAMP BRACKET | *6 | COOLER PIPE CLAMP |
| *7 | RADIATOR RESERVOIR TANK | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | w/ Stop and Start System | - | - |
| *1 | CLUTCH DISC ASSEMBLY | *2 | FLYWHEEL SUB-ASSEMBLY |
| *3 | INNER OIL SEAL | *4 | MANUAL TRANSAXLE ASSEMBLY |
| *5 | NO. 1 CLUTCH HOSE | *6 | ONE-WAY CLUTCH ASSEMBLY |
| *7 | RING GEAR SUB-ASSEMBLY | *8 | STARTER ASSEMBLY |
| *9 | TRANSMISSION CONTROL CABLE ASSEMBLY | *10 | FLYWHEEL HOUSING SIDE COVER |
| *11 | SNAP RING | *12 | NO. 3 ENGINE WIRE |
| *13 | CLUTCH COVER ASSEMBLY | *14 | WIRE HARNESS |
| *15 | ENGINE ASSEMBLY | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | ★ | Precoated part |
ILLUSTRATION
| *1 | BLEEDER CLUTCH RELEASE TUBE | *2 | CLUTCH RELEASE BLEEDER SUB-ASSEMBLY |
| *3 | CLUTCH RELEASE CYLINDER TO BLEEDER TUBE | *4 | CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY |
| *5 | MANUAL TRANSAXLE ASSEMBLY | *6 | CLUTCH TUBE BOOT |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Clutch spline grease | - | - |